Increasing energy demand, together with environmental concerns, results in a significant tendency toward the research and development of renewable systems and particularly solar energy. Locating in the sunbelt of earth, Iran has great solar potential. However, due to the noticeable amount of dust activities in the Middle East, there are several challenges in the way of development of the photovoltaic systems. The current article provides a comprehensive literature review on the photovoltaic status in Iran regarding the climate conditions, photovoltaic development potentials, energy policies within the country, and photovoltaic experiences. A regionally focused review of the conducted works is provided to investigate the effect of dust activities on the output performance of photovoltaic systems. A focus on dust origins, frequency, and specifications is a priority in order to analyze its impacts on the performance of photovoltaic systems. Furthermore, a review of cleaning methods to overcome the dust deposition problem is provided. The comprehensive literature review conducted in this article is represented to researchers, designers, and engineers dealing with photovoltaic systems in regions with dust problems such as the Middle East and particularly Iran.
8 July 2014 in IEEE Transactions on Industry Applications
This paper deals with a hybrid energy source consisting of a proton exchange membrane fuel cell, two storage devices, and a load. Generally, this type of source constitutes of nonisolated dc-dc converters. In order to have galvanic isolation for safety reasons and a high voltage ratio, we introduce another system based on the use of three-port isolated dc-dc converters. The storage device can be either a battery or a supercapacitor. This paper presents a control strategy for the hybrid source and includes a global efficiency analysis of power sharing between modules. The proposed system is validated through different simulation results. Additionally, some experimental results are given for the single module operation.
8 February 2016 in IEEE Transactions on Power Electronics
DC distribution power systems are vulnerable to instability because of the destabilizing effect of converter-controlled constant power loads (CPLs) and input filters. Standard stability analysis tools based on averaging linearization techniques can be used only when the switching frequency of the converter is significantly higher than the cutoff frequency of the filter. However, dc distribution systems with a reduced size filter, and consequently a high cutoff frequency, are common in transportation applications. Conventional methods fail to detect instabilities in the system because they do not take into account the switching effect. To overcome this drawback, this paper proposes a discrete-time method to analyze the stability of dc distribution systems. This model is applied here to a dc power system with a CPL. The switching effects and the nonlinearities of the system model are taken into account with a simple discretization approach. The proposed method is able to predict the dynamic properties of the system, such as slow-scale and fast-scale instabilities. An active stabilizer is also included in the system model in order to extend the stability margin of the system. Finally, these observations are validated experimentally on a laboratory test bench.
29 September 2015 in IEEE Journal of Emerging and Selected Topics in Power Electronics
The stability of dc microgrids is influenced by the nonlinear behavior of the converter-controlled loads with constant power characteristics. This nonlinear dynamic, in line with reduced size input filters used in the embedded power distribution of transportation systems, has a degrading effect on the dynamic performance and stability of the system. This paper presents the complete stability analysis of a dc distribution system composed of power electronics-based source and load. For this objective, a discrete-time dynamic model is developed and is applied to the studied system. Here, for the first time, the dynamic effect of the load controller is taken into the system model. In the studied system, the load converter is connected in cascade with the rest of the system, and is equipped with an input LC filter, representing a common distributed architecture for the transportation applications. The controller of the source converter employs an active stabilizer to extend the stability margin of the system. This stabilizer uses high-pass-filtered voltage of the dc bus following with a proportional compensator. The dynamic behavior of the controller and the stabilizer is experimented through a series of laboratory tests. Different load dynamics are implemented to demonstrate the impact of slow and fast load dynamics on the stability of the system.
The presented study conducted a substantial literature review regarding the electrical modeling of photovoltaic panels. All the main models suggested in the literature to predict a photovoltaic panel's electrical behavior were reviewed, and diode-based equivalent electrical circuit models were selected for further investigations. The study performed a step-by-step investigation, comparison, and classification, followed by an in-depth and critical analysis of the art state. All the main diode-based models suggested in the literature were classified. The models' unknown parameters and the corresponding extraction methods were introduced and compared based on their accuracy, computing costs, and applicability. Reviewing the literature indicates that the extracted parameters under standard test conditions must be adjusted to actual environmental conditions to precisely predict a photovoltaic panel's behavior. By taking that into account, all the applied modifications in the literature were introduced and categorized. Finally, the reviewed documents were assessed critically to identify the research gaps and challenges. The analysis noted that although intensive research studies have been done, there are still many challenges to be faced. Thus, some directions for future research are proposed to cope with the remaining shortages. The presented study could be considered a step-by-step guide for anyone who wants to model the electrical behavior of photovoltaic panels under any environmental conditions.
18 August 2021 in IEEE Transactions on Power Electronics
Voltage imbalance poses a challenge to photovoltaic systems. A modular structure based on a three-level boost converter is proposed to address this problem. The three-level boost converter offers advantages, such as a low current ripple and voltage stress, over a classic boost converter. These advantages offset the use of additional elements in the proposed converter circuit. Two capacitors are used in the proposed converter to enable the innovative connection between multiple sources and the three-level boost converter. The second capacitor of the first module is shared with the first capacitor of the second module. This structure is used in conjunction with a controller to balance the voltages in the system. The controller is based on an indirect sliding model, wherein the input current of each energy source and the output voltage balance are considered. The two-module system is simulated using Simulink MATLAB software. The simulation and experimental results validate the proposed system.