11 November 2010 in IEEE Transactions on Vehicular Technology
This paper presents an energy management method in an electrical hybrid power source (EHPS) for electric vehicular applications. The method is based on the flatness control technique (FCT) and fuzzy logic control (FLC). This EHPS is composed of a fuel cell system as the main source and two energy storage sources (ESSs)-a bank of supercapacitors (SCs) and a bank of batteries (BATs)-as the auxiliary source. With this hybridization, the volume and mass of the EHPS can be reduced, because the high energy density of BAT and high power density of SC are utilized. In the proposed novel control strategy, the FCT is used to manage the energy between the main and the auxiliary sources, and the FLC is employed to share the power flow in the ESS between the SC and the BAT. The power sharing depends on the load power and the state of charge of the SC and the BAT. EHPS is controlled by the regulation of the stored electrostatic energy in the dc buses. The main property of this strategy is that the energy management in the power source is carried out with a single general control algorithm in different operating modes, consequently avoiding any algorithm commutation. An EHPS test bench has been assembled and equipped with a real-time system controller based on a dSPACE. The experimental results validate the efficiency of the proposed control strategy.
9 July 2014 in IEEE Transactions on Industrial Electronics
Photovoltaic (PV) systems are one of the main actors in distributed power generation. In particular, in urban contexts, the PV generators can be subjected to mismatching phenomena due to the different orientation of the modules with respect to the sun rays or due to shadowing. In these cases, the maximum power point tracking (MPPT) function must be designed carefully. In this paper, architecture, including one dc/dc converter for each PV generator, is considered. The converters' output terminals are series connected to a high-voltage dc bus, where also a bidirectional dc/dc converter managing the power from/to a storage device is plugged. The functional constraints deriving from the dc/dc converters' connection, the mismatching phenomena, the MPPT capabilities of the inverter, connected with its input terminals at the dc bus, are taken into account in order to determine the best operating point of the system as a whole. The real-time constrained optimization problem is solved by using the particle swarm optimization method, which needs the knowledge of the actual current versus voltage curve of each PV generator. The practical impact of this need is also discussed in the paper. The feasibility and the performances of the proposed approach are experimentally validated by using a laboratory prototype.
22 March 2010 in IEEE Transactions on Industrial Electronics
Employing fuel cell (FC) as main source requires increasing and regulating its output voltage. In this paper, nonisolated dc-dc converter with high voltage ratio is proposed to interface between the FC and high-voltage dc bus. To take into account the low-voltage-high-density characteristics of power sources, a cascaded structure composed of two subconverters in cascade has been chosen and allows obtaining high voltage ratio. The choice of each subconverter is based on source requirements and its performances. Consequently, in this paper, a converter consisting of two-interleaved boost converter is chosen as first subconverter and a three-level boost converter is chosen as second subconverter. Control of the whole system is realized by energy trajectory planning based on flatness properties of the system. The design of trajectories is explained and allows respecting the fuel-cell constraints as main power source. To ensure correct design of the energy trajectories, a noninteger power-law function is used to model the static characteristic of the FC. This law allows investigating the effect of humidity and temperature on the dynamics of the proposed system. The control of both current and voltage balance across the output serial capacitors of the three-level boost converter is ensured by nonlinear controllers based on a new nonlinear model.
29 March 2010 in IEEE Transactions on Vehicular Technology
Fuel-cell vehicles (FCVs) with energy storage (ES) device(s) could result in improved lifetime, performance, fuel economy, and reduced cost. This paper presents the utilization of an ES device consisting of a supercapacitor bank for future electric vehicles with a hydrogen fuel cell (FC) as the main power source. The study mainly focuses on the innovative control law based on the flatness properties for a FC/supercapacitor hybrid power source. Utilizing the flatness principle, we propose simple solutions to the hybrid energy-management and stabilization problems. A supercapacitor module, as a high dynamic and high-power density device, functions to supply energy to regulate the dc-bus energy. The FC, as a slower dynamic source in this system, functions by supplying energy to keep the supercapacitor module charged. To ensure energy-efficient operation of the FC stack, the output current ripple of the FC stack is minimized by parallel boost converters with an interleaving switching technique for a high-frequency ripple by the supercapacitor for a low-frequency ripple. To authenticate the proposed control laws, a test bench is realized in the laboratory. The control algorithm (energy and current control loops) is digitally implemented by dSPACE controller DS1103. Experimental results with small-scale devices (a proton exchange membrane FC (PEMFC) of 500 W, 50 A, and 10 V and a supercapacitor bank of 250 F, 32 V, and 500 A) substantiate the excellent performance during load cycles.
8 July 2014 in IEEE Transactions on Industry Applications
This paper deals with a hybrid energy source consisting of a proton exchange membrane fuel cell, two storage devices, and a load. Generally, this type of source constitutes of nonisolated dc-dc converters. In order to have galvanic isolation for safety reasons and a high voltage ratio, we introduce another system based on the use of three-port isolated dc-dc converters. The storage device can be either a battery or a supercapacitor. This paper presents a control strategy for the hybrid source and includes a global efficiency analysis of power sharing between modules. The proposed system is validated through different simulation results. Additionally, some experimental results are given for the single module operation.
3 October 2011 in IEEE Transactions on Industrial Electronics
Recently, hybrid electrical power sources composed of storage elements and renewable energy sources are known to have made great development. These energy sources are connected to a dc bus and need a dc-to-ac converter to transfer the produced energy to the grid. Three-leg voltage source inverters equipped with an output LC filter are often used. The main objective of this stage is to generate a three-phase sinusoidal voltage with defined amplitude and to ensure the smallest harmonic distortion rate of the output voltage for any load conditions. To satisfy the defined objectives, we present in this paper a new control method based on differential flatness control technique. The main interest of this control method is the possibility to define the behavior of the state variable system in the steady state as well as in transients. The use of only one control loop allows obtaining high dynamic properties of the system which ensure small harmonic distortion rate of the output voltage. Experimental results under balanced, unbalanced, and nonlinear load conditions are presented and validate the effectiveness of the proposed control methods.