Jaemyung Lim

Dr. Jaemyung Lim


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 January 2020 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
JLJaemyung Lim
Jaemyung Lim
CTCoskun Tekes
Coskun Tekes
EAEvren F. Arkan
Evren F. Arkan
ARAhmad Rezvanitabar
Ahmad Rezvanitabar
FDF. Levent Degertekin
F. Levent Degertekin
MGMaysam Ghovanloo
Maysam Ghovanloo
In this article, we present a highly integrated guidewire ultrasound (US) imaging system-on-a-chip (GUISoC) for vascular imaging. The SoC consists of a 16-channel US transmitter (Tx) and receiver (Rx) electronics, on-chip power management IC (PMIC), and quadrature sampler. Using a synthetic aperture imaging algorithm, a Tx/Rx pair, connected to capacitive micromachined ultrasound transducers (CMUTs), can be activated at any time. The Tx generates acoustic waves by driving the CMUT, while the Rx picks up the echo signal and amplify it to be delivered through an interconnect that is driven by a buffer. On-chip logic controls the pulsers that generate the high-voltage (HV)-pulse for Tx. An on-chip PMIC provides 1.8-, 5-, 39-, and 44-V supplies and a clock signal from the two interconnects besides GND. A quadrature sampler down-converts the Rx echo signal to baseband, reducing its bandwidth requirement for the output interconnect. The system design, including transimpedance amplifier (TIA) optimization, based on the equivalent circuit of a specific CMUT is presented. The SoC was fabricated by a 0.18-μm HV CMOS process, occupying 1.5-mm 2 active area and consuming 25.2 and 44 mW from 1.8 to 44 V supplies, respectively. The US Tx and Rx show bandwidths of 32-42 and 32.7-37.5 MHz, respectively. The input-referred noise of the system was measured as 9.66 nA in band with 2-m-long 52 American Wire Gauge (AWG) wire interconnects. The functionality of the GUISoC was verified in vitro by imaging wire targets.

3 March 2023 in Sensors
Verified
Journal Article
Open access
PDF file
ZLZuolin Li
Zuolin Li
JLJunhyuck Lee
Junhyuck Lee
JLJaemyung Lim
Jaemyung Lim
Byunghun LeeByunghun Lee
Byunghun Lee
When it is necessary to detect various physiological signals of the human body, clothing embroidered with near-field effect patterns can be used as a long-term power supply medium to supply power to long-distance transmitters and receivers to form a wireless power supply system. The proposed system uses an optimized parallel circuit to achieve a power transfer efficiency of more than five times higher than that of the existing series circuit. The power transfer efficiency of simultaneously supplying energy to multiple sensors is increased higher than five times and even more when only one sensor is coupled. When powering eight sensors at the same time, the power transmission efficiency can reach 25.1%. Even when eight sensors powered by the coupled textile coils are reduced to one, the power transfer efficiency of the whole system can reach 13.21%. Additionally, the proposed system is also applicable when the number of sensors ranges from 2 to 12.

23 February 2024 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
JLJaeho Lee
Jaeho Lee
BBBeomjun Bae
Beomjun Bae
BKBohyun Kim
Bohyun Kim
JLJaemyung Lim
Jaemyung Lim
Byunghun LeeByunghun Lee
Byunghun Lee
This letter introduces a novel battery charging solution for multiple wearable devices. Using conductive textile interwoven into clothing, our system provides the convenience of on-body charging and the capacity to charge multiple devices concurrently from a single charger. The uniqueness of our approach lies in its capability to achieve load-independent constant current (CC) and constant voltage (CV) charging using a minimalistic component configuration and permitting each device to independently control its charging mode. Empirical results confirm a variation of less than 5% for both CC and CV charging, whereas theoretical evaluations suggest the system's potential to be scaled up to support an infinite number of devices.

22 January 2024 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
SLSanghun Lee
Sanghun Lee
JLJaemyung Lim
Jaemyung Lim
JaeDuk HanJaeDuk Han
JaeDuk Han
A low-dropout (LDO) regulator controlled by an inverter-based amplifier is proposed to accomplish the latest processor power requirements. The proposed inverter-based amplifier provides a high DC gain in low-voltage operation. Furthermore, an auxiliary non-inverting amplifier is adopted to regulate the wider output voltage and enhance power supply rejection ratio (PSRR) performance. The proposed LDO regulator has been implemented in a 28-nm CMOS process and provides an output range of 0.2-1.05 V from the input range of 0.4-1.1 V. With the input voltage of 1 V, the settling time is within 71.8 ns for 50-mV overshoot and 63 ns for 47-mV undershoot. With the low input voltage of 600 mV, the settling time is within 269 ns for 81-mV overshoot and 182 ns for 84-mV undershoot. The measured values of PSRR are 44.3 dB and 25.0 dB at 100 kHz and 10 MHz at 1-V input voltage, respectively. The PSRR with 600-mV input voltage shows 30 dB up to 600 kHz.

28 January 2025 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
YKYounsik Kim
Younsik Kim
SWSung-Min Wee
Sung-Min Wee
KCKyunghoon Chung
Kyunghoon Chung
BYByungchang Yu
Byungchang Yu
JLJaemyung Lim
Jaemyung Lim
OKOh-Kyong Kwon
Oh-Kyong Kwon
This letter proposes a 6T2C pixel circuit designed for LTPS-based AMOLED displays to improve luminance uniformity and reduce flicker across a wide range of variable refresh rates (VRRs). The proposed circuit employs a two-step compensation method to address variations in the threshold voltage and subthreshold slope of driving thin-film transistors (TFTs), improving luminance uniformity. Additionally, it minimizes the hysteresis effect of TFTs using an inducing hole-trapping technique, resulting in lower flicker. The proposed pixel circuit was verified with 48 samples for a 5.8-inch QHD AMOLED display, achieving notable reductions in emission current errors (ECEs) within a VRR range of 15 Hz to 360 Hz. The luminance uniformity performance was improved compared to a previous 7T2C circuit, with measured spatial ECEs of +3.4/−3.4 LSB versus +4.1/−4.2 LSB at the 256th gray level. The flicker performance was also improved, with measured temporal ECEs of +0.4 LSB and −1.1 LSB versus −0.8 LSB and −3.2 LSB at the 16th and 256th gray levels, respectively.

29 July 2024 in IEEE Access
Verified
Journal Article
Open access
SHSungweon Hong
Sungweon Hong
YTYunseob Tae
Yunseob Tae
DLDongjun Lee
Dongjun Lee
GPGijin Park
Gijin Park
JLJaemyung Lim
Jaemyung Lim
JaeDuk HanJaeDuk Han
JaeDuk Han
This paper studies the problem of designing analog circuits to achieve target specifications, which can be formulated as a multi-objective combinatorial optimization (MOCO) under uncertainty. We address this challenging problem using the gm / ID methodology and a reinforcement learning (RL) framework. The proposed fast RL-based analog circuit designer (fRL-AD) maintains circuits’ DC bias conditions while determining their sizing parameters associated with AC characteristics. This ensures robust convergence to optimal sizing parameters across target specifications and proficiently captures layout effects. Specifically, by decomposing the problem into a sequence of feasible problems, our pre-trained RL agent can efficiently seek a solution for each feasible problem by generating states (i.e., candidate solutions) following a learned policy. Since the sequence of feasible regions is designed to approach an optimal solution to our main problem, the RL agent can find a near-optimal solution by sequentially tackling the feasible problems. Remarkably, using better initial points (or states), our approach is more efficient than directly solving the last feasible problem. Furthermore, we introduce an adaptive action space in our RL framework, which can dynamically modulate the size of the action space elements. The proposed method can provide an effective and stable design of various analog circuits, overcoming their traditionally low productivity due to reliance on human expertise and time-consuming simulations to handle uncertainties. We verify the effectiveness of our algorithm via experiments with various analog circuit topologies.