A new, modified version of the cable-suspended Ice and Bedrock Electromechanical Drill (IBED) was designed for drilling in firn, ice, debris-rich ice and rock. The upper part of the drill is almost the same for all drill variants and comprises four sections: cable termination, a slip-ring section, an antitorque system and an electronic pressure chamber. The lower part of the IBED comprises an auger core barrel, reamers, a core barrel for ice/debris-ice drilling and a conventional geological single-tube core barrel or custom-made double-tube core barrel. First, the short and full-scale field versions of the IBED were tested at an outdoor testing stand and a testing facility with a 12.5 m-deep ice well. Then, in the 2018–2019 summer season, the IBED was tested in the field at a site ~12 km south of Zhongshan Station, East Antarctica, and a ~6 cm bedrock core was recovered from a 198 m-deep borehole. A total of 18 d was required to penetrate the ice sheet. The retrieved core samples of blue ice, basal ice and bedrock provided valuable information regarding the Earth's paleo-environment.

Very few studies have emphasized the effects of high-pressure sintering on snow density evolution, even though snow as a type of engineering material is widely used in construction engineering in cold regions for snow pavement, snow runway and polar infrastructure. This study presents new experimental results of snow densification under high pressures of up to 100 MPa for a temperature range from −3.5 to −17.3°C and uniaxial compression at the temperature of −10°C and constant strain rates from 5 × 10⁻⁴ to 10⁻¹ s⁻¹. Results reveal that density evolution of snow to ice under high-pressure sintering can be achieved in a wide temperature range within a duration as short as 5 min. The compressive strength of snow-sintered ice was ~1.2–2.2 times as large as that of water-frozen ice reported by previous work. The orthogonal experiment showed that pressure is a more significant factor affecting the final density in comparison with sintering temperature and time. The increased rates of ice fabrication, low limitations on temperature and reliable sintered snow strength indicate that snow-ice engineering, such as airport construction in Greenland and Antarctica, can be improved by high-pressure sintering of snow to overcome the harsh environment.

The Antarctic bed demonstrates complex behaviour comprising alternating warm- and cold-based areas. However, the distribution of warm- and cold-based areas, basal melting rates, and the structure and age of the basal ice are not yet fully known. In the 2023–2024 season, we drilled an access borehole through 541 m thick ice at Princess Elizabeth Land, 28 km south of the coast. Temperature measurements at the bottom of the borehole revealed a cold underlying base despite a warm-based interface being predicted in advance as the most likely estimate. Our results imply that the Antarctic base can be locally colder than currently assumed, and that thermal models, especially basal boundary conditions, should be carefully specified and provided with the confirmed input data.

Coring sediments in subglacial aquatic environments offers unique opportunities for research on paleo-environments and paleo-climates because it can provide data from periods even earlier than ice cores, as well as the overlying ice histories, interactions between ice and the water system, life forms in extreme habitats, sedimentology, and stratigraphy. However, retrieving sediment cores from a subglacial environment faces more difficulties than sediment coring in oceans and lakes, resulting in low yields from the most current subglacial sediment coring methods. The coring tools should pass through a hot water-drilled access borehole, then the water column, to reach the sediment layers. The access boreholes are size-limited by the hot water drilling tools and techniques. These holes are drilled through ice up to 3000–4000 m thick, with diameters ranging from 10–60 cm, and with a refreezing closure rate of up to 6 mm/h after being drilled. Several purpose-built streamline corers have been developed to pass through access boreholes and collect the sediment core. The main coring objectives are as follows: (i) To obtain undisturbed water–sediment cores, either singly or as multi-cores and (ii) to obtain long cores with minimal stratigraphic deformation. Subglacial sediment coring methods use similar tools to those used in lake and ocean coring. These methods include the following: Gravity coring, push coring, piston coring, hammer or percussion coring, vibrocoring, and composite methods. Several core length records have been attained by different coring methods, including a 290 cm percussion core from the sub-ice-shelf seafloor, a 400 cm piston core from the sub-ice-stream, and a 170 cm gravity core from a subglacial lake. There are also several undisturbed water–sediment cores that have been obtained by gravity corers or hammer corers. Most current coring tools are deployed by winch and cable facilities on the ice surface. There are three main limitations for obtaining long sediment cores which determines coring tool development, as follows: Hot-water borehole radial size restriction, the sedimentary structure, and the coring techniques. In this paper, we provide a general view on current developments in coring tools, including the working principles, corer characteristics, operational methods, coring site locations, field conditions, coring results, and possible technical improvements. Future prospects in corer design and development are also discussed.

As a result of the severe natural environment with oxygen deficit in the Antarctic, using conventional manual work to screw and unscrew the drill pipe increases the labor intensity tremendously and causes an efficiency reduction. Therefore, it would be useful to design a clamper inside the drilling shelter, which could help to assemble and disassemble the ice core barrel with screw connection. This paper describes the design of and experiments with the clamper inside the movable drilling shelter. A related testing stand was also designed and built to experiment on relationships between the clamper motor current versus clamping torque and force. Through experimental data collation and calculation analysis, the following conclusions could be drawn: (1) according to the rotary ability of the Ice and Bedrock Electromechanical Drill (IBED) to calculate and determine the torque of clamper, the clamping torque required to provide by the clamper is 100 N·m; (2) finite element simulation and analysis of the non-standard transmission chain showed that the mechanical reliability of the subparts; (3) the experimental results showed the range of the clamping force and clamping torque of the clamper. The clamping force and clamping torque increased with the increase of clamper DC motor current, presenting proportional linear relationships. The clamper can meet the clamping requirements of IBED for screwing, unscrewing, and clamping, which will be greatly helpful when it is tested in the field.

The study of the fabric and microstructure of ice at the shear margin of the Antarctic ice sheet is of great significance for understanding the ice flow and its contributions to sea level rise. In this study, twenty-three one-meter-long ice cores were drilled from blue ice areas at the shear margin of the Dalk Glacier, Antarctica. The ice fabric and microstructure of these ice cores are analyzed using a G50 fabric analyzer. This study shows that the shallow ice cores in this region present a cluster fabric as a consequence of shear stress. The grain size decreases following the direction of the ice flow towards the exposed bedrock at the end of the glacier, due to the blocking and squeezing by the bedrock. The formation mechanism of the shallow ice layers is that the ice from the original accumulation area flows here, lifted by the bedrock and shaped by the summer ablation and denudation. The basal ice at the shear margin of the Dalk Glacier is strongly rubbed by the bedrock and demonstrates a cluster fabric. The analysis of stable water isotopes shows a weak negative correlation between shallow ice fabric and stable water isotopes with depth. Bedrock topography and shear stress have a greater influence on grain microstructure among different ice cores over long distances at shear margins.