Jialin Hong

Jialin Hong

Auto-generated profile, based on publicly available information

Jialin Hong

Institute of Polar Science and Engineering, Jilin University, Changchun 130021, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 September 2021 in Annals of Glaciology
Verified
Journal Article
Open access
PDF file
YLYazhou Li
Yazhou Li
PTPavel G. Talalay
Pavel G. Talalay
XFXiaopeng Fan
Xiaopeng Fan
BLBing Li
Bing Li
JHJialin Hong
Jialin Hong
Hot-point drills have been widely used for drilling boreholes in glaciers, ice caps and ice sheets. A hot-point drill melts ice through the thermal head at its bottom end. Penetration occurs through a close-contact melting (CCM) process, in which the ice is melted, and the meltwater is squeezed out by the exerted force applied on the thermal head. During the drilling, a thin water film is formed to separate the thermal head from the surrounding ice. For the hot-point drill, the rate of penetration (ROP) is influenced by several variables, such as thermal head shape, buoyancy corrected force (BCF), thermal head power (or temperature) and ice temperature. In this study, we developed a model to describe the CCM process, where a constant power or temperature on the working surface of a thermal head is assumed. The model was developed using COMSOL Multiphysics 5.3a software to evaluate the effects of different variables on the CCM process. It was discovered that the effect of thermal head shape and the cone angle of conical thermal head on ROP is less significant, whereas the increase in the BCF and the power (or temperature) of the thermal head can continuously enhance the ROP.

6 April 2022 in Journal of Glaciology
Verified
Journal Article
Open access
PDF file
JHJialin Hong
Jialin Hong
PTPavel Talalay
Pavel Talalay
TMTeng Man
Teng Man
YLYazhou Li
Yazhou Li
XFXiaopeng Fan
Xiaopeng Fan
NZNan Zhang
Nan Zhang
Very few studies have emphasized the effects of high-pressure sintering on snow density evolution, even though snow as a type of engineering material is widely used in construction engineering in cold regions for snow pavement, snow runway and polar infrastructure. This study presents new experimental results of snow densification under high pressures of up to 100 MPa for a temperature range from −3.5 to −17.3°C and uniaxial compression at the temperature of −10°C and constant strain rates from 5 × 10−4 to 10−1 s−1. Results reveal that density evolution of snow to ice under high-pressure sintering can be achieved in a wide temperature range within a duration as short as 5 min. The compressive strength of snow-sintered ice was ~1.2–2.2 times as large as that of water-frozen ice reported by previous work. The orthogonal experiment showed that pressure is a more significant factor affecting the final density in comparison with sintering temperature and time. The increased rates of ice fabrication, low limitations on temperature and reliable sintered snow strength indicate that snow-ice engineering, such as airport construction in Greenland and Antarctica, can be improved by high-pressure sintering of snow to overcome the harsh environment.

18 January 2021 in Annals of Glaciology
Verified
Journal Article
Open access
PDF file
YLYazhou Li
Yazhou Li
XFXiaopeng Fan
Xiaopeng Fan
PTPavel Talalay
Pavel Talalay
YDYinke Dou
Yinke Dou
SLSiyu Lu
Siyu Lu
JHJialin Hong
Jialin Hong
In glaciology, snow–firn temperature at 10 m is considered a representation of the mean annual air temperature at the surface (MAAT) of the studied site. Although MAAT is an important parameter in ice-sheet investigations, it has not been widely measured in Antarctica. To measure the 10 m snow–firn temperature in Antarctica, a shallow hot-point drill system is designed. In this simple and lightweight system, a hot-point drill can melt boreholes with a diameter of 34 mm in the snow–firn to a depth of 30 m and a temperature sensors string can measure the borehole temperature precisely. In the 2018/19 field season, 16 boreholes along the Zhongshan–Dome A traverse were drilled, and the borehole temperature was measured. Although certain problems existed pertaining to the hot-point drill, a total depth of ~244 m was successfully drilled at an average penetration rate of ~10 m h−1. After borehole drilling, ~12–15 h were generally required for the borehole to achieve thermal equilibrium with the surroundings. Preliminary results demonstrated that the 10 m snow–firn temperature along the traverse route was affected by the increasing altitude and latitude, and it decreased gradually with an increase in the distance from Zhongshan station.

21 December 2020 in Annals of Glaciology
Verified
Journal Article
Open access
PDF file
PTPavel Talalay
Pavel Talalay
JHJ. Hong
J. Hong
Recently, innovations in ice drilling have yielded considerable improvements to existing drilling techniques, as well as innovative drilling technologies that can be used in new types of applications. However, some specific challenges have to be addressed for improving existing drilling methods and developing new ones: (1) combination and unification of different drilling systems; (2) facilitating ice core breaking; (3) improving existing systems and developing new rapid-access ice drilling systems; (4) reliable elimination of ice hydraulic fracturing problems; (5) developing new environment-friendly methods of drilling in the sub-glacial lake sediments; and (6) design of unconventional ice drilling systems. Possible solutions to these problems are presented herein.

9 April 2020 in Journal of Tribology
Verified
Journal Article
Closed access
PDF file
JHJialin Hong
Jialin Hong
PTPavel Talalay
Pavel Talalay
NZNan Zhang
Nan Zhang
XFXiaopeng Fan
Xiaopeng Fan
Ice friction is one of the major technical issues in almost every application involving ice as one of the moving parts. Very few studies have placed emphasis on the effects of temperature on ice friction at low velocities, although this is important in the transportation of heavy loads in cold regions using sleds, particularly at the onset of sled movement. In this study, a linear tribometer was designed to move a surface of ice over the test surfaces under constant sliding velocity and load. We present new experimental results of the kinetic friction of ice on stainless steel and polytetrafluoroethylene (PTFE) substrates at low velocities and a wide range of temperatures to a minimum of −60 °C. The results show a strong reduction in friction with increase in temperature. Low friction at low velocities and high temperatures may be owing to the thicker quasi-liquid water from pre-melting at the points of sliding contact, while high friction at low velocities and low temperatures can be caused by the low mobility of the surface molecules. The huge difference between the thermal conductivities of stainless steel and PTFE as well as the relatively high glass transition temperature of PTFE most likely account for the divergence of their coefficient of kinetic friction (COF) curves.

8 September 2025 in Water
Verified
Journal Article
Open access
PDF file
MSMikhail A. Sysoev
Mikhail A. Sysoev
PTPavel Talalay
Pavel Talalay
XFXiaopeng Fan
Xiaopeng Fan
NZNan Zhang
Nan Zhang
DGDa Gong
Da Gong
TWTing Wang
Ting Wang
Hot-point thermal drills are among the simplest and most compact tools for drilling boreholes in ice by melting. They are widely used in glaciological and geophysical research, including subsurface access on Earth and planetary missions. This study focuses on electrically heated hot-point drills. It presents a comparative review of four analytical models commonly used to describe thermal penetration into ice. Our theoretical processing and computation allow for the analysis and optimization of the drilling performance of thermal drill heads. The predictive accuracy of the adapted model was evaluated through comparison with experimental data obtained using the RECAS-200 thermal sonde. Based on the analysis of various sources and calculations using the modified model, a set of recommendations is proposed for early-stage estimation of drilling parameters and assessment of thermal drilling efficiency in the design of hot-point drills for autonomous and resource-constrained missions.