Purpose: This study aims to investigate the effects of five different printing parameters, namely, printing speed (PS), printing temperature/nozzle temperature/extrusion temperature, heated-bed temperature, raster angle (RA) and layer height (LT), on mechanical properties. Design/methodology/approach: American Society for Testing and Materials (ASTM) standards were used for the specimen design. Then, the Taguchi method was used for the design of the experiment and an L16 orthogonal array was preferred. Tensile, Shore D and surface roughness tests were conducted on polylactic acid test specimens. The test results were analyzed using the signal-to-noise ratio and analysis of variance (ANOVA). Findings: As a result of the study, it was seen that RA is the most important parameter for the tensile strength, PS is for the hardness and LT is for the surface roughness. According to the ANOVA results, the effects of the RA, PS and LT on the maximum tensile strength, hardness and surface roughness were 41.59%, 69.51% and 44.6%, respectively. Originality/value: To the best of the authors’ knowledge, this study is one of the most comprehensive parameter optimization studies for additive manufacturing in the literature because it includes five different printing parameters and three mechanical test procedures.
3 June 2024 in International Journal of Simulation Modelling
Nowadays, laser welding is a powerful joining method. Thanks to the advantages it has, its usage area is increasing day by day. However, getting the desired result from the laser welding process is possible with the proper welding parameter selections. Otherwise, many problems may be encountered, including significantly incomplete penetration. For this reason, parameter selection has been discussed in many studies in the literature. At this point, validated numerical simulation models are precious. Since these models reduce experiment costs and save time. Especially numerical simulation of the structural steel, which is the one of most used materials, is crucial. In this study, the effects of laser power (LP) and welding speed (WS), which are among the vital parameters of laser welding, on weld width and stress were investigated numerically and statistically. Structural steel was selected as the material, and the Taguchi method was carried out for the simulation case study design. Simufact Welding software was used for simulation studies, and simulations were carried out thermomechanical. Thus, more realistic results were obtained via the thermomechanical method. One of the simulation results was verified through an experimental study. The results were evaluated with signal-to-noise (S/N) ratio and a statistical analysis of variance (ANOVA), and as a result of the study, it was seen that the welding speed was a more effective parameter, the optimal parameter combination was found to be 3500 W for laser power and 40 mm/s for welding speed to get maximum weld width and minimum equivalent stress. In addition, it was observed that correctly created simulation studies may provide very close results to experimental studies.
Purpose: This study aims to investigate the effects of heat treatment on the mechanical and visual properties of PLA-wood samples. Three different heating temperatures and three different durations were applied to determine their impact on tensile strength, hardness, moisture resistance, dimensional stability, surface quality and visual appearance. Design/methodology/approach: Samples were designed according to ASTM standards and produced via additive manufacturing. A full factorial experimental design was used. A total of 11 experimental groups were created: one untreated, one dried-only and nine heat-treated. Mechanical and physical evaluations included tensile testing, Shore D hardness, surface roughness, moisture absorption and visual color changes using a custom-built low-cost colorimeter developed specifically for this study. Findings: Heat treatment improved mechanical strength and moisture resistance of PLA-wood. The highest tensile strength was achieved at 100 °C for 90 min, showing a 12.8% increase compared to the untreated group. Heat treatment increased hardness and brittleness while reducing elongation and moisture absorption. Dimensional changes stabilized after 100 °C for 90 min, and color generally darkened with increasing temperature. These findings indicate that heat treatment is effective for improving the performance and appearance of PLA-wood composites. Originality/value: This is one of the most comprehensive heat treatment studies on PLA-wood in the literature, incorporating five distinct testing methods. A novel, low-cost colorimeter was developed for visual analysis. The results contribute significantly to the limited body of work on PLA-wood biocomposites and offer guidance for enhancing their functional and aesthetic properties through post-processing.
Crash boxes in vehicles are one of the passive safety measures that aim to reduce injury to passengers and damage to the vehicle during a collision. Their function is to absorb the mechanical energy resulting from a collision by deforming plastically. Considering human safety, not only the energy must be damped, but also the forces acting on the passengers must be controlled. This force control can be adjusted to some extent using trigger mechanisms. There is a wide variety of research on hole type triggers, but they concentrated on traditional shapes; unique or hybrid shapes have not been sufficiently tested. This study examined the effects of various hole profiles with equal areas on dynamic mechanical performances of Al 6063-T6 rectangular crash boxes. Four types of trigger shapes were formed: upward keyhole, downward keyhole, U-shaped, and S-shaped. The dynamic performance evaluation was carried out experimentally by testing five types of geometries, the fifth one being the geometry without any trigger. In addition, dynamic Finite element analyses were conducted and validated using the experimental data, with the aim of employing the Finite element models in future geometry improvement studies. The experimental results were interpreted with some common evaluation parameters: peak force, crash force efficiency, mean crash force, and total energy absorption. The downward keyhole profile generally gave the best results, while the lowest peak force was observed in the U-shaped profile.
Additive manufacturing (AM) techniques, especially fused deposition modeling (FDM), offer significant advantages in terms of cost, material efficiency, and design flexibility. In this study, the mechanical performance of biodegradable PLA/PHA composite samples produced via FDM was optimized by evaluating the influence of key printing parameters—layer height, printing orientation, and printing speed—on both the tensile and compressive strength. A full factorial design (3 × 3 × 3) was employed, and all of the samples were triplicated to ensure the consistency of the results. Grey relational analysis (GRA) was used as a multi-objective optimization method to determine the optimal parameter combinations. An analysis of variance (ANOVA) was also conducted to assess the statistical significance of each parameter. The ANOVA results revealed that printing orientation is the most significant parameter for both tensile and compression strength. The optimal parameter combination for maximizing mechanical properties was a layer height of 0.1 mm, an X printing orientation, and a printing speed of 50 mm/s. This study demonstrates the effectiveness of GRA in optimizing the mechanical properties of biodegradable composites and provides practical guidelines to produce environmentally sustainable polymer parts.