Crash boxes in vehicles are one of the passive safety measures that aim to reduce injury to passengers and damage to the vehicle during a collision. Their function is to absorb the mechanical energy resulting from a collision by deforming plastically. Considering human safety, not only the energy must be damped, but also the forces acting on the passengers must be controlled. This force control can be adjusted to some extent using trigger mechanisms. There is a wide variety of research on hole type triggers, but they concentrated on traditional shapes; unique or hybrid shapes have not been sufficiently tested. This study examined the effects of various hole profiles with equal areas on dynamic mechanical performances of Al 6063-T6 rectangular crash boxes. Four types of trigger shapes were formed: upward keyhole, downward keyhole, U-shaped, and S-shaped. The dynamic performance evaluation was carried out experimentally by testing five types of geometries, the fifth one being the geometry without any trigger. In addition, dynamic Finite element analyses were conducted and validated using the experimental data, with the aim of employing the Finite element models in future geometry improvement studies. The experimental results were interpreted with some common evaluation parameters: peak force, crash force efficiency, mean crash force, and total energy absorption. The downward keyhole profile generally gave the best results, while the lowest peak force was observed in the U-shaped profile.
The increasing interest in sustainable materials has led to the development of bio-based composites for additive manufacturing applications. This study aimed to investigate the influence of key printing parameters and new-generation infill patterns together on the maximum compressive force of PLA–wood bio-composites produced by Material Extrusion. By optimizing this material, low-cost wood-like products can be produced. New-generation 3D infill patterns (octet, cubic-subdivision, and lightning which is a biomimetic infill pattern) infill densities, printing temperatures, and layer heights were selected as variables/factors, and the Taguchi method was applied for design of the experiment. The signal-to-noise ratio and Analysis of Variance were used to evaluate the statistical significance and contribution of each parameter to the mechanical response. The signal-to-noise ratio indicated that the optimal printing settings were as follows: printing temperature, 205 °C; infill density, 80%; infill pattern, octet; and layer height, 0.2 mm (7123.4 N). ANOVA results showed that infill density was the most significant factor affecting maximum compressive force at 60%, while infill pattern also exhibited a notable effect. According to these results, infill density and infill pattern are the most important factors for achieving high compressive strength. These findings suggest that optimizing infill architecture and density can improve the mechanical performance of PLA–wood composites, also they can offer assistive design guidelines for lightweight and eco-friendly components.
With the new manufacturing technologies, it has been possible to machine hard metals efficiently. During high-speed machining (HSM) of high-strength steel, the poor surface integrity of the workpiece affects the performance of the process. Surface roughness, microstructure, microhardness and residual stress are key performance indices for surface integrity directly controlled by tool wear and cutting parameters. In this study, high-feed milling (HFM) of a pocket on test samples made of DIN 1.2344 ESR mould steel with 55 HRc hardness was carried out on the CNC vertical milling machine. Three different cutting speeds and five different feed rates were used. At the end of the machining, tool wear was measured using a microscope. Subsequently, X-ray diffraction and hole drilling procedures were used to quantify residual stresses on machined test specimens. The results showed that under cutting conditions, the highest tensile residual stress was attained at fz = 0.78 mm·tooth−1, v = 127.58 m·min−1, and the highest compressive residual stress at fz = 0.5 mm·tooth−1, v = 127.58 m·min−1, on the workpiece surface. The most suitable cutting parameters were reported as fz = 0.63 mm·tooth−1 and v = 70 m·min−1 cutting speed when tool wear and residual stresses are considered together.
8 July 2022 in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Kaza anında araçların hızları ve kütleleri sebebiyle yüksek miktarda enerji açığa çıkmakta ve bu enerjinin uygun şekilde sönümlenmesi gerekmektedir. Düzgün sönümlenemeyen enerji iç parçalara, sürücüye ve yolculara zarar verecek kuvvetlerin oluşmasına sebep olarak hayati sorunlara yol açar. Araçlarda bu sönümlemeyi yapabilmek için devletlerin, kurumların ve sigorta şirketlerinin öne sürdüğü kriterleri karşılayabilecek özel tasarlanmış çarpışma kutusu adındaki parçalara ihtiyaç duyulmaktadır. Sürdürülebilirlik, çevre, yakıt tasarrufu gibi kavramlarla beraber araçlarda hafifliğin ön plana çıkması ve artan rekabet, kaza dışında âtıl duran çarpışma kutuları üzerinde önemli çalışmalara yol açmıştır. Bu nedenlerle, çarpışma kutularının kinetik enerjiyi emme performansı, üretilebilirliği, maliyeti, hafifliği göz önünde bulundurularak uygun seçimler yapılmalıdır. Bu çalışma, çarpışma kutusunun performansını artırıcı temel faktörleri ele alan kapsamlı bir literatür araştırmasını içermektedir. Çalışmada, çarpışma kutularının enerji sönümleme yeteneği; geometri, malzeme ve dolgu gibi üç temel başlık altında ele alınmıştır. Bu kapsamda, literatürdeki çalışmalar incelenerek çarpışma kutuları ile gerçekleştirilen enerji emilimi konusundaki önemli noktalar derlenmiştir.
31 March 2022 in International Journal of Automotive Science And Technology
Reducing fuel consumption, increasing road holding and overcoming air resistance are the main goals in the field of vehicle aerodynamics. Therefore, controlling the lift-ing forces is very important for vehicle stability. Generally, lifting forces are used as low as possible and an additional downforce is required in order to increase road holding. Various vehicle parts have been developed to control the airflow in passen-ger cars. One of them is the rear lower diffuser which is located on the floor of the ve-hicle. In this study, the length value of the base diffuser is kept constant as the base edge, and the effects of the diffuser location position on the lifting and drag force at 60 km/h with angles of 10º, 15º, 20º and 30º are investigated. These effects are also investigated comparatively according to flat-floor geometry. As a result of the study, it is observed that the use of the diffuser reduces the negative effects by changing the lifting force from positive to negative, and it provides a significant advantage in drag force compared to the flat-floor geometry, however, the angle changes do not have a significant effect.