KONSTANTINOS CHATZIMANOLIS

Mr. KONSTANTINOS CHATZIMANOLIS

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 April 2020 in Journal of Materials Chemistry C
Verified
Journal Article
Open access
PDF file
CZChristos Zervos
Christos Zervos
MTMarinos Tountas
Marinos Tountas
KCKONSTANTINOS CHATZIMANOLIS
KONSTANTINOS CHATZIMANOLIS
CPChristos Polyzoidis
Christos Polyzoidis
Emmanuel KymakisEmmanuel Kymakis
Emmanuel Kymakis
An alternate use of PEAI for enhancing the performance of inverted perovskite solar cells is demonstrated, by employing it as an anti-solvent during the perovskite fabrication process. The results show an enhancement of the open-circuit voltage as compared to the PEAI post treatment.

26 February 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Nikolaos TzoganakisNikolaos Tzoganakis
Nikolaos Tzoganakis
DTDimitris Tsikritzis
Dimitris Tsikritzis
KCKONSTANTINOS CHATZIMANOLIS
KONSTANTINOS CHATZIMANOLIS
Xiaodong ZhuangXiaodong Zhuang
Xiaodong Zhuang
Emmanuel KymakisEmmanuel Kymakis
Emmanuel Kymakis
The most widely used material as a hole-transport layer (HTL) for effective normal perovskite solar cells (PSCs) is still 2,2′,7,7′-Tetrakis[N, N-di(4-methoxyphenyl)amino]-9,9′-spirobifluorene (Spiro-OMeTAD), which requires heavy doping with the hydroscopic Lithium bis(trifluoromethanesulfonyl)imide (Li-ΤFSI). However, the long-term stability and performance of PCSs are frequently hampered by the residual insoluble dopants in the HTL, Li+ diffusion throughout the device, dopant by-products, and the hygroscopic nature of Li-TFSI. Due to the high cost of Spiro-OMeTAD, alternative efficient low-cost HTLs, such as octakis(4-methoxyphenyl)spiro[fluorene-9,9′-xanthene]-2,2′,7,7′-tetraamine) (X60), have attracted attention. However, they require doping with Li-TFSI, and the devices develop the same Li-TFSI-derived problems. Here, we propose Li-free 1-Ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (EMIM-TFSI) as an efficient p-type dopant of X60, resulting in a high-quality HTL with enhanced conductivity and deeper energy levels The optimized X60:EMIM-TFSI-enabled devices exhibit a higher efficiency of 21.85% and improved stability, compared to the Li-TFSI-doped X60 devices. The stability of the optimized EMIM-TFSI-doped PSCs is greatly improved, and after 1200 hr of storage under ambient conditions, the resulting PSCs maintain 85% of the initial PCE. These findings offer a fresh method for doping the cost effective X60 as the HTL with a Li-free alternative dopant for efficient, cheaper, and reliable planar PSCs.

14 December 2022 in Energy Technology
Verified
Journal Article
Open access
NTNikolaos Tzoganakis
Nikolaos Tzoganakis
BFBoxu Feng
Boxu Feng
MLMichalis Loizos
Michalis Loizos
KCKONSTANTINOS CHATZIMANOLIS
KONSTANTINOS CHATZIMANOLIS
MKMiron Krassas
Miron Krassas
Emmanuel KymakisEmmanuel Kymakis
Emmanuel Kymakis
Herein, an azulene–pyridine molecule (AzPy) is implemented in inverted perovskite solar cells (PSCs) for increasing the power conversion efficiency (PCE) and the stability of the devices. The first goal is achieved by depositing a thin layer of AzPy on top of the hole charge transport layer (HTL). The surface engineering of HTL with AzPy improves the perovskite layer formation, thus increasing light absorption and reducing bulk nonradiative recombination while protecting the perovskite from degradation species from the HTL. This approach increases the mean PCE by approximately 6%. The second goal of improving the stability of the devices is mainly achieved by replacing the hydrophilic bathocuproine (BCP) with the more hydrophobic AzPy. By the development of an AzPy layer over the electron transport layer (ETL), the stability of the PSCs is increased under ambient conditions and thermal or light stress, without affecting the PCE. The two proposed interface engineering approaches are both implemented in the device in conjunction with the perovskite surface treatment with n‐hexylammonium bromide, resulting in devices that deliver a PCE of 20.42% and increased thermal and light stability, thus retaining 90% of their initial PCE for more than 1200 h under ambient conditions.

18 April 2024 in IEEE Journal on Flexible Electronics
Verified
Journal Article
Closed access
GPGeorge Psaltakis
George Psaltakis
KRKonstantinos Rogdakis
Konstantinos Rogdakis
KCKONSTANTINOS CHATZIMANOLIS
KONSTANTINOS CHATZIMANOLIS
Emmanuel KymakisEmmanuel Kymakis
Emmanuel Kymakis
The ever-increasing number of Internet of Thing devices requires the development of edge-computing platforms to address at low power consumption the associated demand for big data processing while minimizing cloud communication latency. Neuromorphic computation is a viable solution to avoid an unsustainable energy cost, however, achieving stable memristive switching is a complex process. Mixed-halide perovskite resistive memories is a promising technology that usually requires an extensive experimental characterization procedure till a stable operation mode is reached, resulting in an abundance of data that should be manually processed. In this study we build a dataset for pattern recognition based on thousands of images of experimental current-voltage (I-V) characteristics of solution-processed, and thus printable, mixed halide perovskite memristors. We have categorized our experimental data into seven distinct categories of memristive behaviour depending on the shape of the I-V curves. A machine learning (ML) approach is implemented using a convolutional neural network (CNN) trained using this image-based dataset. After the training phase, the CNN is able to categorize any new experimental I-V across the seven generic types, while a binary categorization process, by splitting the experimental data into those exhibiting good or bad switching characteristics, is demonstrated with validation accuracies of up to 91%. Overall, it is shown that this ML-based pattern recognition approach can assist in identifying how many of the tested memristive devices exhibit stable, optimum switching dynamics, and upon expanding the model, it could predict which characterization parameters are most influential toward achieving an efficient device operation.