High power DPSS UV lasers having high repetition rates (>100 kHz) are significant part of the cost of a laser Si micro-processing system. An alternative inexpensive solution, MOPA based IR fiber lasers, have been used to machine Si with high energy shaped pulses. This investigation evaluates the single pulse machining performance of a pulse shapeable IR (1062 nm) fiber laser and a DPSS UV (355 nm) laser on Si substrates and directly compares their performance. The machined depth data was measured with a white light interferometer and the finishing quality examined for surface defects with a SEM. Theoretical analysis demonstrated rapid heating effects by taking account of the dynamic optical and thermal properties of Si for given IR laser shaped pulses. The results show that high quality Si surface micro-processing can benefit from using the more flexible, more reliable, and pulse shapeable IR fiber laser at high repetition rates which no conventional solid state IR or UV laser could achieve.
27 March 2009 in IEEE Journal of Selected Topics in Quantum Electronics
The advances in design, performance, cost reduction, and brightness for the modern Yb fiber lasers have opened up the possibility of redefining the processing options of semiconductor materials at a wavelength of 1064 nm. The usual laser of choice for Si processing is the 355- or 266-nm diode-pumped solid-state system. The provision of a new master oscillator power amplifier (MOPA)-based high-brightness Yb-based fiber laser configuration has provided a range of pulse parameters (30-50 ns full-width at half-maximum), peak powers approaching ~2 GWmiddotcm-2, and pulse repetition rates up to 500 kHz. These processing parameters offer a broad range of material response characteristics. This paper provides a preliminary analysis of the response of Si to the new MOPA-based Yb laser operating at maximum average power of 20 W. Results presented here show no signs of the usual thermally induced deleterious effects (microcracking, heavy recast layers, and surface damage) normally associated with Si interactions at 1064 nm. Volumetric etch rates of up to 230 000 000 mum3middots-1 were observed with a high-quality percussion drilling interaction at a repetition rate of 25 kHz and an average power of 20 W.
Vergence-accommodation conflict (VAC) is a common annoying issue in near-eye displays using stereoscopy technology to provide the perception of three-dimensional (3D) depth. By generating multiple image planes, the depth cues can be corrected to accommodate a comfortable 3D viewing experience. In this study, we propose a multi-plane optical see-through augmented reality (AR) display with customized reflective polarization-dependent lenses (PDLs). Leveraging the different optical powers of two PDLs, a proof-of-concept dual-plane AR device is realized. The proposed design paves the way to a compact, lightweight, and fatigue-free AR display.
1 November 2021 in International Journal of Human-Computer Studies
Sub-millisecond response time with a refresh rate higher than 2000 frames per second (fps) and no degradation of the contrast ratio or diffraction efficiency is demonstrated in working liquid crystal on silicon (LCOS) spatial light modulators (SLMs) with 8-bit grey levels of amplitude and phase modulations. This makes possible to achieve an information bandwidth of about 190 Gb s-1 with a 4k LCOS operating at 10-bit phase modulation levels. The normalised contrast stays at almost the unit level for a frame rate up to 1700 fps and at higher than 0.9 for 2500 fps. The diffraction efficiency stays above -1.0 dB for a frame rate up to 2400 fps. Such a fast response allows us to eliminate image blurring in replaying a fast movie.
A method to enable smectic A (SmA) liquid crystal (LC) devices to switch uniformly and hence fast from the clear state to a scattered state is presented. It will allow the reduction of the switching time for a SmA LC panel of 1 × 1 m2 changing from a clear state to a fully scattered state by more than three orders to a few tens of milliseconds. Experimental results presented here reveal that SmA LC scattering initiates from the nucleated LC defects at the field gradient of the applied electric field usually along the edges of the panel electrode and grows laterally to spread over a panel, which takes a long time if the panel size is large. By patterning the electrodes in use, it is possible to create a large number of field gradient sites near the electrode discontinuities, resulting in a uniform and fast switching over the whole panel and the higher the pattern density the shorter the panel switching time. For the SmA LC panels used here, the ITO transparent electrodes are patterned by laser ablation and photolithography. It is shown that the defect nucleation time is much shorter than the growth time of the scattered region, hence it is possible to use the density of the field gradient sites to control the uniformity and switching time of a panel. Furthermore, the patterned SmA panels have a lower switching voltage than that of the non-patterned ones in general. Graphical Abstract