Probing polycrystals' stress: The way that a polycrystalline material deforms is in part determined by internal stresses between and within crystal grains. Hayashi et al. developed an x-ray method for mapping the intragranular stresses in a polycrystalline material. They found surprisingly large stresses, which are important for the fundamental understanding of how these materials will fail. This method will work for other materials and provides important information for multiscale deformation modeling. Science , this issue p. 1492
Recently, nondestructive evaluation of the stresses localized in grains was achieved for plastically deformed low-carbon steel using scanning three-dimensional X-ray diffraction (S3DXRD) microscopy with a conical slit. However, applicable metals and alloys were restricted to a single phase and evaluated stress was underestimated due to the fixed Bragg angles of the conical slit optimized to αFe. We herein propose S3DXRD with a rotating spiral slit adaptable to various metals and alloys and accurate stress evaluation with sweeping Bragg angles. Validation experiments with a 50-keV X-ray microbeam were conducted for low-carbon steel as a body-centered cubic (BCC) phase and pure Cu as a face-centered cubic (FCC) phase. As a result of orientation mapping, polygonal grain shapes and clear grain boundaries were observed for both BCC and FCC metals. Thus, it was demonstrated that S3DXRD with a rotating spiral slit will be applicable to various metals and alloys, multiphase alloys, and accurate stress evaluation using a X-ray microbeam with a higher photon energy within an energy range determined by X-ray focusing optics. In principle, this implies that S3DXRD becomes applicable to larger and thicker metal and alloy samples instead of current miniature test or wire-shaped samples if a higher-energy X-ray microbeam is available.
Plastically deformed low-carbon steel has been analyzed by nondestructive three-dimensional orientation and strain mapping using scanning three-dimensional X-ray diffraction microscopy (S3DXRD). However, the application of S3DXRD is limited to single-phase alloys. In this study, we propose a modified S3DXRD analysis for dual-phase alloys, such as ferrite–pearlite carbon steel, which is composed of grains detectable as diffraction spots and a phase undetectable as diffraction spots. We performed validation experiments for ferrite–pearlite carbon steel with different pearlite fractions, in which the ferrite grains and the pearlite corresponded to the detectable grains and an undetectable phase, respectively. The regions of pearlite appeared more remarkably in orientation maps of the ferrite grains obtained from the carbon steel samples than that of the single-phase low-carbon steel and increased with the increase in the carbon concentration. The fractions of the detectable grains and the undetectable phase were determined with an uncertainty of 15%–20%. These results indicate that the proposed modified analysis is qualitatively valid for dual-phase alloys comprising detectable grains and an undetectable phase.
Neutron radiography is regarded as complementary to X-ray radiography in terms of transmittance through materials, but its spatial resolution is still insufficient. In order to achieve higher resolution in neutron imaging, several approaches have been adopted, such as optical magnification and event centroiding. In this paper, the authors focused on modification of the scintillator. A Gd3Al2Ga3O12:Ce single-crystal scintillator was applied to neutron radiography for the first time and a spatial resolution of 10.5 μm was achieved. The results indicate that this material can be a powerful candidate for a new neutron scintillator providing a resolution in micrometer order by optimizing the optical system and increasing the scintillator luminosity.
20 November 2006 in Fatigue & Fracture of Engineering Materials & Structures
Understanding of deformation and degradation of bulk metals under loading is necessary to improve the safety and environmental performance of mechanical components such as automobile parts. One of the key parameters in mechanical characterization is strain. Large strains that affect reliability can often be measured as changes in the crystallographic orientation. Electron backscatter diffraction (EBSD) method can measure strains only on the sample surface. However, since strain distribution varies under constrained conditions, nondestructive measurement inside the material is necessary to determine the actual mechanical response of the material. We propose scanning three-dimensional x-ray diffraction microscopy, 3DXRD, in combination with the in-situ measurement tensile tester. High-energy synchrotron radiation x-ray enables internal measurements, and the diffraction method using scanning microbeam and conical slits enables measurement of three-dimensional distributions. The development of a special in-situ loading device that can be used in the limited space of 3DXRD setup has realized measurement of deformation behavior of steel during the tensile loading process. This technique enabled the nondestructive measurement of crystallographic orientation change in 80 grains before and after plastic deformation. It was found that even when grains exhibited similar orientations before plastic deformation, it was not the case after plastic deformation. The magnitude of crystallographic orientation change due to tensile loading is considered to depend on local constraints such as the orientation, grain size, 3-dimensional position, and shape of adjacent grains. Nondestructive strain measurement techniques as shown here are considered important for the advancement of evaluation methods for deformation and deterioration of mechanical components.