Anaerobic ponds have the potential to contribute to low carbon wastewater treatment, however are currently restricted by long hydraulic residence time (HRT) which leads to large land requirements. A two-stage anaerobic pond (SAP) design was trialled against a single-stage control (CAP) over four HRTs down to 0.5 days, to determine the lowest HRT at which the ponds could operate effectively. No statistical differences were observed in particulate removal between the ponds over all four HRTs, suggesting solids loading is not a critical factor in AP design. Significantly higher biogas production rates were observed in the SAP than the CAP at 1.5 d and 1.0 d HRT, and microbial community profiling suggests the two-stage design may be facilitating spatial separation of the anaerobic digestion process along reactor length. Hydrogenotrophic methanogensis dominated over aceticlastic, with acetate oxidisation a likely degradation pathway. Experimental tracer studies were compared to CFD simulations, with the SAP showing greater hydraulic efficiency, and differences more pronounced at shorter HRTs. Greater flow recirculation between baffles was observed in CFD velocity profiles, demonstrating baffles can dissipate preferential flow patterns and increase effective pond volume, especially at high flow rates. The study demonstrates the potential of APs to be operated at shorter HRTs in psychrophilic conditions, presenting an opportunity for use as pre-treatments (in place of septic tanks) and primary treatment for full wastewater flows. Two-stage designs should be investigated to separate the stages of the anaerobic digestion process by creating preferential conditions along the pond length. GRAPHICAL ABSTRACT
1 November 2013 in Proceedings of the Institution of Civil Engineers - Water Management
Rainwater harvesting from hard roofing can provide safe water to meet the basic domestic needs of several hundred million people in low-income countries. However, rainwater harvesting has a higher household cost than other low-technology water supplies such as protected springs. The storage tank is the most expensive part of the infrastructure required for rainwater harvesting: reducing this cost will enable rainwater harvesting to become a viable water source for many more households in low-income countries. This paper assesses the overall costs and different cost components of rainwater storage tanks. Costs are compared across a selection of tanks prefabricated in factories in Uganda, Kenya and the UK and constructed in situ in Uganda. Constructed tanks were always found to be cheaper than prefabricated ones. Tank size was an important factor, and it was found that tank cost per litre decreases as size increases. For all tank types, materials were the greatest cost.
15 September 2016 in Environmental Science: Water Research & Technology
To ensure adequate access to sanitation in developing economies, off-grid single household sanitation has been proposed which obviates the need for significant infrastructure capital investment. Whilst treatment at this scale is most efficient when coupled to source separation (i.e. urine from faeces), existing source separation solutions have proved difficult to implement in this context. In this study, screw extrusion is therefore investigated to provide ‘post-flush’ source separation. Both screw characteristics and operational boundary conditions were evaluated. Preferential screw characteristics included tapering of the shaft and progressive pitch reduction, linked to a small extrusion aperture, the combination of which enhanced solids extrusion efficiency and promoted higher solids concentration in the extruded fraction. Whilst maximum extrusion efficiency was observed at high rotational speeds (over 400 rpm), this also promoted free water transport. Operating below 300 rpm instead introduced selectivity for transport of faecal sludge over urine, enabling phase separation. Constraining the volumetric ratio of urine to faeces also enhanced the extrusion rate of faecal sludge by increasing feed viscosity sufficient to overcome backpressure imposed by unmasticated food particles that would otherwise restrict separation. Importantly, this study demonstrates the feasibility of screw extrusion for ‘post flush’ separation of urine and faeces which constitutes a significant advancement towards realising sanitation at a single household scale.
An anaerobic pond (AP) for treatment of temperate domestic wastewater has been studied as a small works sludge management strategy to challenge existing practice which comprises solids separation followed by open sludge storage, for up to 90 days. During the study, effluent temperature ranged between 0.1 °C and 21.1 °C. Soluble COD production was noted in the AP at effluent temperatures typically greater than 10 °C and was coincident with an increase in effluent volatile fatty acids (VFA) concentration, which is indicative of anaerobic degradation. Analysis from ports sited along the AP's length, demonstrated VFA to be primarily formed nearest the inlet where most solids deposition initially incurred, and confirmed the anaerobic reduction of sludge within this chamber. Importantly, the sludge accumulation rate was 0.06 m3 capita−1 y−1 which is in the range of APs operated at higher temperatures and suggests a de-sludge interval of 2.3–3.8 years, up to 10 times longer than current practice for small works. Coincident with the solids deposition profile, biogas production was predominantly noted in the initial AP section, though biogas production increased further along the AP's length following start-up. A statistically significant increase in mean biogas production of greater than an order of magnitude was measured between winters (t(n=19) = 5.52, P < 0.001) demonstrating continued acclimation. The maximum methane yield recorded was 2630 mgCH4 PE−1 d−1, approximately fifty times greater than estimated from sludge storage (57 mgCH4 PE−1 d−1). Anaerobic ponds at small works can therefore enable sludge reduction and longer sludge holding times than present thus offsetting tanker demand whilst reducing fugitive methane emissions currently associated with sludge storage, and based on the enhanced yield noted, could provide a viable opportunity for local energy generation.
1 September 2012 in Proceedings of the Institution of Civil Engineers - Engineering Sustainability
An anaerobic waste stabilisation pond (AWSP) has been assessed to enable energy neutral wastewater treatment at decentralised works. During start-up, chemical oxygen demand (COD) removal efficiency was comparable to full-scale AWSPs operated in moderate climates, thereby establishing the potential for treating wastewater in the less conducive European climate. The linear relationship between COD removal and time demonstrated that the AWSP had not reached steady-state, indicating further improvement in COD removal is expected. Data modelled on a 10 000 population equivalent catchment indicated that integrating an AWSP upstream of trickling filters presented the optimum configuration to minimise on-site electrical demand. Anaerobic WSP can generate sufficient electricity onsite to offset electrical demand. Anaerobic WSP can generate sufficient electricity onsite to offset electrical demand, recording a net on-site energy balance of +379·5 kWhe d-1. Using an AWSP for on-site sludge treatment also reduced exported sludge volume, markedly reducing the wastewater treatment total carbon dioxide equivalent emissions (carbon footprint) compared to conventional technologies. This study established AWSP as a significant future technology for sustainable decentralised wastewater treatment.