Alba Regina Turin

Mrs. Alba Regina Turin

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 April 2023 in Metals
Verified
Journal Article
Open access
PDF file
JRJomar José Knaip Ribeiro
Jomar José Knaip Ribeiro
ATAlba Regina Turin
Alba Regina Turin
Yamid E. Nuñez de la RosaYamid E. Nuñez de la Rosa
Yamid E. Nuñez de la Rosa
PQPedro Victorio Caetano Abrantes Quadros
Pedro Victorio Caetano Abrantes Quadros
Oriana Palma CalabokisOriana Palma Calabokis
Oriana Palma Calabokis
PBPaulo César Borges
Paulo César Borges
This study aimed at the mechanical characterization, on a nanometric scale, of the constituents obtained for different fractions in duplex stainless-steel plates subjected to 850, 950, 1000, and 1150 °C heating treatments via hardness measurements and determining their influences on the fretting wear behavior of the studied steel. The obtained ferrite (α)-, austenite (γ)-, and sigma (σ)-phase fractions were determined using optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) techniques. The mechanical characterization was carried out using hardness measurement and fretting wear techniques via nanoindentation. For comparison purposes, the Vickers microhardness was also characterized to determine the effect of the σ phase, which eventually formed, on the obtained microstructure properties as a whole. Two distinct behaviors were observed, depending on the eventual formation of σ phase as a function of the treatment temperature: (i) specimens treated at 850 and 950 °C showed a hardening effect (HV0.5 values of 333 ± 15 and 264 ± 13, respectively) due to σ-phase precipitation (hereafter termed ‘as-aged’), and (ii) specimens treated at 1000 and 1150 °C (with HV0.5 values of 240 ± 13 and 249 ± 4, respectively) showed no σ-phase precipitation (hereafter termed ‘as-solubilized’). The increases in the microhardness values for the as-aged specimens were attributed to the hardness of the σ-phase precipitates (which showed nanohardness values varying in the 8.0–8.5 GPa range), which was approximately twice that of the austenite and ferrite grains (both phases showed nanohardness values in the 3.6–4.1 GPa range, on average). When formed (for fractions on the order of 8% and 3% at 850 and 950 °C, respectively), σ phase was mainly observed at the α/γ grain interfaces or boundaries. Fretting wear tests, using a diamond sphere with a radius of 10 μm as the counter body and a load of 20 mN, revealed the same wear mechanisms in the α/γ matrix for all studied conditions. However, as-solubilized specimens (heat-treated at 1000 and 1150 °C) displayed higher resistance to fretting micro-wear in the austenitic grains compared to the ferritic grains, indicating lower plastic deformation in the respective wear scars on the obtained tracks. In particular, as-aged specimens (heat-treated at 850 and 950 °C) exhibited lower coefficients of friction due to their higher surface resistances. The localized wear at σ-phase grains was much less pronounced than at ferrite and austenite grains. Overall, this study provides valuable insights into the mechanical behavior of microstructural changes in duplex steel at the nanometric scale.

31 December 2025 in Steel Research International
Verified
Journal Article
Open access
ATAlba Regina Turin
Alba Regina Turin
JRJomar José Knaip Ribeiro
Jomar José Knaip Ribeiro
APAlex Pizzatto
Alex Pizzatto
Oriana Palma CalabokisOriana Palma Calabokis
Oriana Palma Calabokis
Yamid E. Nuñez de la RosaYamid E. Nuñez de la Rosa
Yamid E. Nuñez de la Rosa
PBPaulo César Borges
Paulo César Borges
Duplex stainless steels (DSSs) have outstanding mechanical properties and corrosion resistance. However, operating conditions and/or inadequate heat treatments can induce precipitation of deleterious phases or change the proportion of ferrite (α) and austenite (γ) phases. This study evaluates the impact of ageing at 850 and 950 °C and solubilization at 1000 and 1150 °C treatments on pitting and crevice corrosion of DSS UNS S32205. Cyclic polarization tests revealed that samples with a more balanced α/γ ratio (≈50/50), that is, the base material (BM) and that solubilized at 1000 °C, exhibited the lowest corrosion rate (0.044–0.074 μm/year) and better repassivation capacity (E R ≈ 0.96 V). Conversely, the 1150 °C treatment led to reduced corrosion resistance (0.158 ± 0.009 μm/year) and is associated with a reduction in the %Cr in α. Pitting is present in the aged conditions only. Moreover, the BM and 1000 °C samples showed the lowest crevice corrosion susceptibility, presenting the lowest volume loss (1 × 10 6 μm 3 cm −2 ) and current densities (≈1000 μA cm −2 ), followed by samples treated at 1150, 950, and 850 °C. Therefore, the results show that ageing treatments make UNS S32205 susceptible to pitting and crevice corrosion, which is related to the deleterious phase fraction and the α/γ ratio imbalance.

1 January 2023 in Anais Do Congresso Internacional de Engenharia Mecânica E Industrial
Verified
Conference Paper
Open access
PDF file
ATAlba Regina Turin
Alba Regina Turin
JRJomar José Knaip Ribeiro
Jomar José Knaip Ribeiro
PQPedro Victorio Caetano Abrantes Quadros
Pedro Victorio Caetano Abrantes Quadros
PBPaulo César Borges
Paulo César Borges
Anais do Congresso Internacional de Engenharia Mecânica e Industrial (2764-4294) - Efeito De Tratamentos Isotérmicos Na Microestrutura E Microdureza Do Aço Inoxidável Duplex Uns S32205 (Saf 2205)