Flood has occurred many times in Malaysia and it has greatly affected the residents that live in flood risk area such as Bukit Merah. Due to the climate change and land use changes issues, the flood and drought events seem to be occurred more frequently in larger scale in Bukit Merah. Therefore, the objectives of this study were to develop the hydrologic model for Bukit Merah and to forecast the flood magnitude for next twenty years by considering the factor of climate change and land use changes via HEC-HMS. After developing the hydrologic model of Bukit Merah, the model has been calibrated and validated with the coefficient of determination, R2 = 0.9066 and 0.9575 respectively. The results showed that the simulated stream flow was closely fit to the observed streamflow, therefore it was reliable. Then, the model was used to simulate the streamflow for next twenty years by using predicted future rainfall data obtained from NAHRIM. The simulated peak discharge to the Bukit Merah Reservoir for next twenty years was 113.7 m3/s. Then, the scenarios of excess rainfall and extremely lack of rainfall were simulated. In extremely lack of rainfall scenario, the peak discharge to the Bukit Merah Reservoir decreased by 76.87 % while for the excess rainfall scenario, the peak discharge has increased 379 %. After that, the Curve Number (CN) of the basin has been increased by 20% and it was assumed to have 70% of impervious area according to the future development in Perak. Then, the model was simulated but the peak discharge to Bukit Merah Reservoir remain unchanged, recorded as 113.7 m3/s. Hence, this paper outlined that climate change has the biggest impact on the magnitude of streamflow but the land use changes do not give much effects to the magnitude of streamflow in Bukit Merah.
One of the disadvantages of normal concrete is the high self-weight of the concrete. Density of the normal concrete is in the range of 2200 kg/m3 to 2600 kg/ m3. This heavy self-weight make it as an uneconomical structural material. Advantages of expended polystyrene beads in lightweight concrete is its low in density which can reduce the dead load (self-weight) Improper disposal of the large quantity of palm oil fuel ash which has been produced may contribute to environmental problem in future. In this study, an alternative of using palm oil fuel ash as a cement replacement material is to improve the properties of lightweight concrete. The tests conducted in this study were slump test, compression strength, splitting tensile and water absorption test. These samples were cured under water curing condition for 7, 28 and 56 days before testing. Eight types of mixtures were cast based on percentage (25%, 50%) of polystyrene beads replacement for control samples and (25%, 50%) of polystyrene beads by different ratio 10%, 15%, and 20% replacement of palm oil fuel ash, respectively. Samples with 25% polystyrene beads and 10% palm oil fuel ash obtained the highest compressive strength which is 16.8 MPa, and the splitting tensile strength is 1.57 MPa. The water absorption for samples 25%, 50% polystyrene and 20% palm oil fuel ash is 3.89% and 4.67%, respectively which is lower compared to control samples.
30 April 2018 in Journal of Civil Engineering, Science and Technology
These days, sustainability has become a primary concern as the large amount of natural resources are being used to produce materials such as concrete. Concrete from the construction industry constitutes the major proportion of construction waste. This could bring negative impact including depletion of natural resources, pollution, increasing landfill space, and high cost of waste disposal. All of these negative impacts are the sustainability issues that should be concentrated on. Hence, alternative methods have been introduced in order to reduce waste by recycling concrete waste. One of the alternative methods that can be used is by reusing recycled concrete aggregates (RCA) from discarded waste cubes. RCA can be used to produce new concrete but it will generally have a lower performance compared to normal concrete. Thus, the present study introduces an alternative method which is by reusing the RCA as a water filter medium to remove phosphorus from wastewater. Phosphorus is one of the inorganic compounds found in wastewater that can lead to environmental problems such as eutrophication. Based on previous studies, many types of materials with various chemical compositions have been used for phosphorus removal from wastewater. Therefore, this study demonstrates the ability of RCA as an alternative method for phosphorus removal from wastewater. In addition, three different factors have been considered in the removal of phosphorus namely, different initial concentration of phosphorus, different sizes of RCA and dosage of RCA used during the treatment process. Based on the experiments conducted, the lowest initial concentration of phosphorus of 10 mg/L, the smallest RCA size ranging between 0mm to 5mm and the highest RCA dosage of 50g resulted in the highest percentage of phosphorus removal in wastewater.
18 December 2023 in Archives of Metallurgy and Materials
Bamboo Ash is a safer and more sustainable building material. It is possible to use bamboo ash as a partial cement replacement as an alternative to cement application and also to reduce pollution. For this study, the main purpose is to determine the compressive strength and water absorption of cement sand brick containing bamboo ash. Laboratory tests such as compression tests and water absorption tests on cement sand brick with bamboo ash as a partial replacement for cement have been conducted. The mixes with various ratios using bamboo ash are 5%, 7%, and 10%. The specimen size for cement sand brick is 215 mm long, 102.5 mm wide, and 65 mm deep according to BS3921:1985. The results from the specimens containing Bamboo Ash have been compared to the control specimens. The water absorption test results increase as the percentage of Bamboo Ash increases due to particle size and air void, but the compressive strength decreases at 28 days.