Czestochowa University of Technology, Department of Mechanics and Fundamentals of Machinery Design, Faculty of Mechanical Engineering and Computer Science, 73 Dąbrowskiego Str., 42-201 Częstochowa, Poland
Auto-generated profile, based on publicly available information
Justyna Garus
Czestochowa University of Technology, Department of Mechanics and Fundamentals of Machinery Design, Faculty of Mechanical Engineering and Computer Science, 73 Dąbrowskiego Str., 42-201 Częstochowa, Poland
The study analyzed the influence of materials and different types of damping on the dynamic stability of the Bernoulli-Euler beam. Using the mode summation method and applying an orthogonal condition of eigenfunctions and describing the analyzed system with the Mathieu equation, the problem of dynamic stability was solved. By examining the influence of internal and external damping and damping in the beam supports, their influence on the regions of stability and instability of the solution to the Mathieu equation was determined.
Porous asphalt has excellent permeability and larger air voids. Due to the low stability strength of asphalt binder with aggregates, Malaysia uses porous asphalt roads for lightweight vehicle road transportation. Numerous studies indicate utilizing Recycled High-Density Polyethylene in porous asphalt road surface. As a result, it was utilised as an additional binder material to enhance the asphalt binder. The main purpose of this study is to investigate the stability of modified porous asphalt samples and evaluate the optimum percentage of HDPE plastic waste from 3%, 6% and 9%. The aggregates, asphalt properties, Marshall Parameters and waster absorption test are in comply with JKR Standard and PWD 2008. At 3% of plastic addition has improved the stability of porous asphalt specimens. Adding plastic waste as a binder helps strengthen asphalt binding.
18 December 2023 in Archives of Metallurgy and Materials
Bamboo Ash is a safer and more sustainable building material. It is possible to use bamboo ash as a partial cement replacement as an alternative to cement application and also to reduce pollution. For this study, the main purpose is to determine the compressive strength and water absorption of cement sand brick containing bamboo ash. Laboratory tests such as compression tests and water absorption tests on cement sand brick with bamboo ash as a partial replacement for cement have been conducted. The mixes with various ratios using bamboo ash are 5%, 7%, and 10%. The specimen size for cement sand brick is 215 mm long, 102.5 mm wide, and 65 mm deep according to BS3921:1985. The results from the specimens containing Bamboo Ash have been compared to the control specimens. The water absorption test results increase as the percentage of Bamboo Ash increases due to particle size and air void, but the compressive strength decreases at 28 days.
13 May 2021 in Archives of Metallurgy and Materials
This work concerns the study of the coatings for the ultrasound frequency range as a quasi one-dimensional phononic crystal structure protecting a sea object against high resolution active sonar in the frequency range most commonly found for this type of equipment. The topology of the examined structure was optimized to obtain a band gap in the 2.2-2.3 MHz frequency band. For this purpose, a genetic algorithm was used, which allows for optimal distribution of individual elements of the ultrasound multilayer composite. By optimal distribution is meant to achieve a structure that will allow minimal reflectance in a given frequency range without height reflectance peaks with a small half width. Analysis of the wave propagation was made using the Transfer Matrix Method (TMM). As part of the research, 15 and 20-layer structures with reflectance at the level of 0.23% and 0.18%, respectively, were obtained. Increasing the number of layers in the analyzed structures resulted in finding such a distribution in which a narrow band of low reflectance was obtained, such distributions could also be used as bandpass filters. The use of a genetic algorithm for designing allows to obtain modern coatings, the characteristics of which result from the structure.
11 April 2024 in Archives of Metallurgy and Materials
The study analyzed the influence of periodic and aperiodic stiffness distribution for the four-element Bernoulli-Euler beam on the first two eigenfrequencies and the dynamic stability of the system. The influence of increasing the ratio of cross-sections of the analyzed elements was also analyzed. Significant differences were found in eigenfrequencies and dynamic stability. Using the variational Hamilton principle, the equation of motion was derived, on the basis of which the values of the eigenfrequencies were determined, and the transformation into the form of the Mathieu equation made it possible to determine the dynamic stability for the analyzed structures.