Rong A

Dr. Rong A


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2016 in Journal of Aerospace Engineering
Verified
Journal Article
Closed access
LGLi Guoxiang
Li Guoxiang
Liping PangLiping Pang
Liping Pang
MLMeng Liu
Meng Liu
YDYang Dongsheng
Yang Dongsheng
YQYu Qingni
Yu Qingni
RARong A
Rong A
Carbon dioxide removal assembly (CDRA) is an essential subsystem in an air revitalization system (ARS) to control CO2 concentration in a long-term manned spacecraft cabin. At the same time, it is a main power consumption subsystem. CO2 concentration control performance and power consumption are both key factors that need to be considered. To design this subsystem reasonably, some basic processes are analyzed carefully in this paper, such as mass and heat transfer processes in CO2 adsorption beds, power consumption for fan and electric heater, and entropy generation in heat transfer process. The relationship between CDRA and other subsystems are also analyzed carefully. Based on these analyses, a multiobjective optimal method is developed in this paper. Its objective functions are specified as cabin CO2 concentration level, power consumption, and entropy generation. The optimal parameters are air velocity, absorption bed length, adsorption time (half cycle time), and molecular sieve mass loaded in ...

27 June 2018 in Energies
Verified
Journal Article
Open access
PDF file
Liping PangLiping Pang
Liping Pang
SLShuxin Li
Shuxin Li
MLMeng Liu
Meng Liu
RARong A
Rong A
ALAicheng Li
Aicheng Li
FMFanxin Meng
Fanxin Meng
The aerodynamic heating of a high-speed vehicle is destined to lead to a continuous fuselage temperature rise. However, its airborne thermal load rises exponentially. This will severely limit the thermal endurance of the high-speed vehicle and the working time of the electronic equipment. A jet-propelled high-speed vehicle usually uses fuel to generate thrust, so fuel thermal management technology has had much attention paid to it. During the vehicle design, its total amount of fuel should match its flight envelope. However, determining the amount of carried fuel is very difficult because it is affected by many factors. In order to analyze the relationship between the above influence factors and the flight envelope, a typical fuel thermal management system is set up for high-speed vehicles. Its dynamic characteristic equations are built correspondingly. A conception of thermal endurance is further presented to reveal the maximum flight time. Some flight conditions are used to analyze the influence of the main design parameters on the thermal endurance of high-speed vehicles. The results can help to design the parameters of fuel thermal management systems for high-speed vehicles.

24 May 2023 in Energies
Verified
Journal Article
Open access
PDF file
RWRi Wang
Ri Wang
BQBin Qi
Bin Qi
YZYixia Zhou
Yixia Zhou
RARong A
Rong A
SDSujun Dong
Sujun Dong
A metal fiber burner is proposed for structural thermal tests for the test model of hypersonic vehicles. In order to guide the design of the burner, we conduct Fluent simulations on a cylindrical metal fiber burner with a properly selected thermal diffusion model, a heat transfer model between the gas and solid phase, a radiation model with a metal porous media, and a gaseous combustion chemistry mechanism. After validating the simulation, the combustion and heating characteristics of the burner were further analyzed. The results show that under the condition of no specimen, when the firing rate increases from 120 kW/m2 to 240 KW/m2, the maximum gas temperature and the downstream gas temperature of the metal fiber increase by 6.21% and 8.55%, respectively, the outer surface temperature of the metal fiber increases by 6.42%, and the stable gas temperature downstream of the metal fiber reaches the maximum value at an equivalence ratio of 1. After the specimen is added, the internal and downstream gas temperatures of the metal fiber are significantly reduced, while the upstream gas and outer surface temperatures of the metal fiber show no significant changes. When the specimen diameter changes from 139mm to 98mm, the gas temperature and fiber surface temperature change is small, while the surface heat flux of the specimen significantly increases from 12.7 KW to 22.7 KW. It can be seen that when designing the test parameters, the surface heat flux of the specimen can be adjusted by adjusting the distance between the combustion surface and the specimen.

6 October 2023 in Aerospace
Verified
Journal Article
Open access
PDF file
RWRi Wang
Ri Wang
LFLou Fengfei
Lou Fengfei
BQBin Qi
Bin Qi
RARong A
Rong A
YZYuanye Zhou
Yuanye Zhou
SDSujun Dong
Sujun Dong
In this paper, aimed at the problem of large temperature gradient thermal testing with the typical sharp wedge leading edge structure of a hypersonic vehicle, a subsonic high-temperature combustion gas heating (SHCH) test device is used to conduct a series of experiments on the heat flux simulation ability of subsonic high-temperature combustion gas in the stagnation point region. Firstly, for a hypersonic vehicle with a flying height of 24 km and Mach number range of 4~6.5, the stagnation point heat flux in the head area is obtained by numerical calculation of a typical leading edge structure, which is used as the experimental target of the thermal structure test. Secondly, an experimental specimen with a Gardon heat flux meter is designed with the same shape and size as the specimen in the numerical simulations to prepare for the subsequent SHCH test. Thirdly, a method to determine the combustion gas temperature based on a Kriging surrogate model is proposed. CFD numerical simulation is conducted using the SHCH test model, and the numerical calculation results are used as the training dataset. The Kriging surrogate model is used to establish an approximate fitting relationship between the stagnation point heat flux and experimental parameters under SHCH conditions. The corresponding combustion gas temperature values are found, respectively, with the hypersonic aerodynamic heat flux at Mach 5.0~5.4 as the target value. Finally, stagnation point heat flux testing of low-speed and high-temperature combustion gas is performed at different combustion gas temperatures. The experimental and target values obtained from hypersonic aerodynamic thermal simulations are compared and analyzed to verify the heating capacity of SHCH and the feasibility of hypersonic aerothermal simulation testing.


1 January 2015
Verified
Conference Paper
Open access
PDF file
RARong A
Rong A
Liping PangLiping Pang
Liping Pang
JWJun Wang
Jun Wang
MLMeng Liu
Meng Liu
QYQingni Yu
Qingni Yu
Silica gel has a potential ability to adsorb water vapor and contaminant together, so it has been focused recently in indoor air environment. In this paper, the performance of silica gel adsorbing trace gas pollutions in isothermal column is studied through theoretical methods. The model of the adsorption column system was set up based on mass conservation, linear driving force model and Henry's Law. An implicit differential method was used to solve the model in the Matlab environment and to obtain the breakthrough curves. Seven simulation experiments were conducted to discuss the effect of overall mass transfer coefficient, Henry parameter and gas velocity on adsorption process. From the result it indicated that the overall mass transfer coefficient impacts the breakthrough point enormously. Henry parameter reflects the adsorption capacity of adsorbent particle, high Henry constant affords long lifespan of adsorbent. Furthermore, high efficient and long-term use of adsorbent cannot obtain without reasonable gas velocity.