For aerogels in metal thermal protection system (MTPS), radiative heat transfer will participate in the thermal transport process. Therefore, the influence of the emissivity of the coupling interface between metal and aerogels on thermal insulation performance is considered an important research focus. In this paper, CFD numerical simulation is performed to study the influence of emissivity on the performance with different extinction coefficients at different boundary temperatures. The finite volume method and the discrete ordinate method are used to solve the govern equations. The results show that when the boundary temperatures are 600 K and 2100 K, the extinction coefficient is 50 m−1, and the reduction percentage of the effective thermal conductivity with an emissivity of 0.2 can be up to 47.5% and 69.8%, compared to the system with an emissivity of 1. Thus, the reduction in emissivity has a good effect on the thermal insulation performance of the MTPS at a higher boundary temperature for materials with small extinction coefficients.
A metal fiber burner is proposed for structural thermal tests for the test model of hypersonic vehicles. In order to guide the design of the burner, we conduct Fluent simulations on a cylindrical metal fiber burner with a properly selected thermal diffusion model, a heat transfer model between the gas and solid phase, a radiation model with a metal porous media, and a gaseous combustion chemistry mechanism. After validating the simulation, the combustion and heating characteristics of the burner were further analyzed. The results show that under the condition of no specimen, when the firing rate increases from 120 kW/m to 240 KW/m, the maximum gas temperature and the downstream gas temperature of the metal fiber increase by 6.21% and 8.55%, respectively, the outer surface temperature of the metal fiber increases by 6.42%, and the stable gas temperature downstream of the metal fiber reaches the maximum value at an equivalence ratio of 1. After the specimen is added, the internal and downstream gas temperatures of the metal fiber are significantly reduced, while the upstream gas and outer surface temperatures of the metal fiber show no significant changes. When the specimen diameter changes from 139mm to 98mm, the gas temperature and fiber surface temperature change is small, while the surface heat flux of the specimen significantly increases from 12.7 KW to 22.7 KW. It can be seen that when designing the test parameters, the surface heat flux of the specimen can be adjusted by adjusting the distance between the combustion surface and the specimen.
In this paper, aimed at the problem of large temperature gradient thermal testing with the typical sharp wedge leading edge structure of a hypersonic vehicle, a subsonic high-temperature combustion gas heating (SHCH) test device is used to conduct a series of experiments on the heat flux simulation ability of subsonic high-temperature combustion gas in the stagnation point region. Firstly, for a hypersonic vehicle with a flying height of 24 km and Mach number range of 4~6.5, the stagnation point heat flux in the head area is obtained by numerical calculation of a typical leading edge structure, which is used as the experimental target of the thermal structure test. Secondly, an experimental specimen with a Gardon heat flux meter is designed with the same shape and size as the specimen in the numerical simulations to prepare for the subsequent SHCH test. Thirdly, a method to determine the combustion gas temperature based on a Kriging surrogate model is proposed. CFD numerical simulation is conducted using the SHCH test model, and the numerical calculation results are used as the training dataset. The Kriging surrogate model is used to establish an approximate fitting relationship between the stagnation point heat flux and experimental parameters under SHCH conditions. The corresponding combustion gas temperature values are found, respectively, with the hypersonic aerodynamic heat flux at Mach 5.0~5.4 as the target value. Finally, stagnation point heat flux testing of low-speed and high-temperature combustion gas is performed at different combustion gas temperatures. The experimental and target values obtained from hypersonic aerodynamic thermal simulations are compared and analyzed to verify the heating capacity of SHCH and the feasibility of hypersonic aerothermal simulation testing.
The metal fibre surface combustion structure has the characteristics of strong thermal matching ability, short response time, and strong shape adaptability. It has more advantages in the thermal test of complex hypersonic vehicle surface inlet, leading edge, etc. In this paper, a method of aerodynamic thermal simulation test based on metal fibre surface combustion is proposed. The aim of the study was to create a uniform target heat flow on the inner wall surface of a cylindrical specimen by matching the gas jet flow rate and the geometry of the combustion surface. The research adopted the optimisation design method based on the surrogate model to establish the numerical calculation model of a metal fibre combustion jet heating cylinder specimen. One hundred sample points were obtained through Latin hypercube sampling, and a database of design parameters and heat flux was established through numerical simulation. The kriging surrogate model and the non-dominated sequencing genetic optimisation algorithm with elite strategy were adopted. A bi-objective optimisation design was carried out with the optimisation objective of the coincidence between the predicted and the target heat flux on the inner wall of the specimen. The results showed that the average relative errors of heat flow density on the specimen surface were 8.8% and 6% through the leave-one-out cross-validation strategy and the validation of six test sample points, respectively. The relative error values in most regions were within 5%, which indicates that the established kriging surrogate model has high prediction accuracy. Under the optimal solution conditions, the numerical calculation results of the heat flow on the inner wall of the specimen were in good agreement with the target heat flow values, with an average relative error of less than 5% and a maximum value of less than 8%. These results show that the optimisation design method based on the kriging surrogate model can effectively match the thermal test parameters of metal fibre combustion structures.