Developing bone scaffolds can greatly improve the patient’s quality of life by accelerating the rehabilitation process. In this paper, we studied the process of composite polycaprolactone supercritical foaming for tissue engineering. The influence of graphene oxide and reduced graphene oxide on the foaming parameters was studied. The structural and mechanical properties were studied. The scaffolds demonstrated mechanical flexibility and endurance. The co-culturing and live/dead tests demonstrated that the obtained scaffolds are biocompatible. Different composite scaffolds induced various surface cell behaviors. The experimental data demonstrate that composite foams are promising candidates for in vivo medical trials.

Oil production is a complex process that can be made more efficient by applying gas enhanced oil recovery (EOR) methods. Thus, it is essential to know the minimum miscibility pressure (MMP) and minimum miscibility enrichment (MME) of gas in oil. Conventional slim-tube experiments for the measurement of MMP require hundreds of millilitres of real or recombined oil and last over 30 days. Advances in microfluidic technology allow the reduction of the amount of fluid and the time required in determining MMP (or MME), hence making the process rapid. In this study, we developed a microfluidic model with a stochastically distributed pore network, porosity of 74.6% and volume of 83.26 nanolitres. Although the volume was six orders of magnitude smaller than the slim tube, it retained the same proportions, guaranteeing a proper comparison between the tests. This microfluidic chip allowed the study of the MMP of n-decane with carbon dioxide at two different temperature conditions. The experimental results coincided with the results received both from conventional and microfluidic experiments. Furthermore, a numerical simulation of a section of the microfluidic model under the experimental conditions presented results within acceptable margins of the experimental ones. The results of the presented methodology indicate the potential to replace conventional technology for the measurement of MMP with microfluidic technology. Its promise lies in accelerating laboratory tests and increasing the reliability of experimental results and, subsequently, the quality of field gas EOR operations.

The efficiency of electronic microchip-based devices increases with advancements in technology, while their size decreases. This miniaturization leads to significant overheating of various electronic components, such as power transistors, processors, and power diodes, leading to a reduction in their lifespan and reliability. To address this issue, researchers are exploring the use of materials that offer efficient heat dissipation. One promising material is a polymer–boron nitride composite. This paper focuses on 3D printing using digital light processing of a model of a composite radiator with different boron nitride fillings. The measured absolute values of the thermal conductivity of such a composite in the temperature range of 3–300 K strongly depend on the concentration of boron nitride. Filling the photopolymer with boron nitride leads to a change in the behavior of the volt–current curves, which may be associated with the occurrence of percolation currents during the deposition of boron nitride. The ab initio calculations show the behavior and spatial orientation of BN flakes under the influence of an external electric field at the atomic level. These results demonstrate the potential use of photopolymer-based composite materials filled with boron nitride, which are manufactured using additive techniques, in modern electronics.

To increase the oil recovery factor (RF), enhanced oil recovery (EOR) methods are applied: chemical, gas, thermal, and combined ones. Standard laboratory research methods for selecting and optimizing EOR technologies require a lot of time and resources, as well as core material, which is often in short supply. To optimize the selection of reagents and field development technologies, the use of microfluidic technology is proposed i.e. conducting experiments in reservoir conditions using microfluidic chips with a porous structure, reproducing the properties of the core of the target field. The main advantages of conducting tests in micromodels are the low duration and the ability to visualize filtration processes, which makes it possible to evaluate the behavior of fluids in reservoir conditions. This paper considers the modern application of microfluidics for the selection of EOR agents and stimulation methods and the status of this technology in the oil and gas industry. The use of microfluidic chips for screening surfactants and polymers, as well as studying the mechanism of low-mineralized water action is described. Conducting microfluidic tests to optimize gas and thermal EOR, which became possible due to the development and improvement of technology, is considered.

This work focuses on the fabrication of niobium through silicon vias (TSV) superconductors interconnects. The effect of supercycle of sequential oxidation and chemical etching process on the through-etch wall quality was investigated. It was experimentally shown that the use of supercycle in the fabrication process leads to significant improvement of the TSV wall quality and removal of the defect type—scallops. After 12 times repetitions of supercycles a dissipative bonding of superconducting strips on the front and back side of the sample is observed. The critical current density of such coupling is 5 × 10⁴ A cm⁻². The critical ratio of substrate thickness to hole diameter at which electrical coupling is formed is 3:1.