Lili Ma

Dr. Lili Ma


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 April 2023 in Materials
Verified
Journal Article
Open access
PDF file
LMLili Ma
Lili Ma
ZZZaiyang Zhao
Zaiyang Zhao
YWYurong Wu
Yurong Wu
JSJingjing Sun
Jingjing Sun
SGSiyong Gu
Siyong Gu
HZHouan Zhang
Houan Zhang
For investigating the influence mechanism underlying ultrafine Ti(C, N) within micron Ti(C, N)-based cermets, three cermets including diverse ultrafine Ti(C, N) contents were employed. In addition, for the prepared cermets, their sintering process, microstructure, and mechanical properties were systematically studied. According to our findings, adding ultrafine Ti(C, N) primarily affects the densification and shrinkage behavior in the solid-state sintering stage. Additionally, material-phase and microstructure evolution were investigated under the solid-state stage from 800 to 1300 °C. Adding ultrafine Ti(C, N) enhanced the diffusion and dissolution behavior of the secondary carbide (Mo2C, WC, and (Ta, Nb)C) under a lower sintering temperature of 1200 °C. Further, as sintering temperature increased, adding ultrafine Ti(C, N) enhanced heavy element transformation behaviors in the binder phase and accelerated solid-solution (Ti, Me) (C, N) phase formation. When the addition of ultrafine Ti(C, N) reached 40 wt%, the binder phase had increased its liquefying speed. Moreover, the cermet containing 40 wt% ultrafine Ti(C, N) displayed superb mechanical performances.

15 April 2024 in Materials
Verified
Journal Article
Open access
PDF file
ZZZaiyang Zhao
Zaiyang Zhao
PJPengmin Jia
Pengmin Jia
YZYuhui Zhang
Yuhui Zhang
LMLili Ma
Lili Ma
JSJingjing Sun
Jingjing Sun
YWYurong Wu
Yurong Wu
The use of metal-coated ceramic powders not only effectively enhances the wettability of the metal–ceramic interface but also promotes a more uniform microstructure in Ti(C,N)-based cermets, which is advantageous for improving their mechanical properties. In this study, ultrafine Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders were synthesized via the spray-drying-in-situ carbothermal reduction method. Subsequently, Ti(C,N)-based cermets were effectively fabricated using the as-prepared ultrafine Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders. The impact of reaction temperature, heating rate, and isothermal time on the phase and microstructure of prepared powders was analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Additionally, the microstructure of the as-sintered cermets was experimentally investigated. The findings reveal that the complete reduction of Co and Ni metal salts, pre-coated on the surface of (Ti,W,Mo,Ta)(C,N) particles, can be achieved through rapid heating (10 °C/min) in a specific temperature range (600–1000 °C) with an isothermal time of 3 h at a lower reduction temperature (1000 °C). The synthesized powders have only two phases: the (Ti,W,Mo,Ta)(C,N) phase and Co/Ni phase, and no other heterogeneous phases were observed with an oxygen content of 0.261 wt.%. Notably, the conventional core–rim structure was not dominant in the cermets obtained from the prepared Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders. Moreover, the heterogeneous segregation effect of the Co/Ni coating on the ultrafine powder particles resulted in a finer microstructure than the traditional cermets with the same composition. However, the grain size is mainly in the range of 0.5–0.8 μm. The weaker residual stresses at the core and rim interfaces and the finer particle distributions could theoretically enhance the toughness of Ti(C,N)-based cermets, simultaneously.

7 June 2026 in Materials
Verified
Journal Article
Open access
PDF file
LMLili Ma
Lili Ma
YXYiping Xu
Yiping Xu
LYLin Yulin
Lin Yulin
Binbin WeiBinbin Wei
Binbin Wei
HZHouan Zhang
Houan Zhang
This study systematically investigated the influence of aluminum nitride (AlN) addition on the microstructure and mechanical properties of Ti(C,N)-based cermets with low Ni/Co and high N contents. The results demonstrate that AlN addition does not alter the phase composition of Ti(C,N)-based cermets, and their microstructure retains the characteristic core–rim morphology. The dissolution of Al atoms from AlN effectively suppressed abnormal growth of Ti(C,N) grains and enhanced the mechanical stability of the binder. Densification and comprehensive mechanical properties strongly depended on the AlN content. Both parameters initially improved with the addition of AlN, peaked at an optimal content of 1.0 wt.%, and then declined upon further addition due to the formation of micropores and brittle agglomerates of Al2O3. At the optimal AlN content of 1.0 wt.%, the cermets demonstrated peak performance: a Vickers hardness of 1676 HV30, a transverse rupture strength of 1486 MPa, and a fracture toughness of 8.8 MPa·m1/2. The results elucidate the dual role of AlN as both a microstructural refiner and a precursor for in situ strengthening of the binder phase.