Houan Zhang

Prof. Dr. Houan Zhang


Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 March 2023 in Materials
Verified
Journal Article
Open access
PDF file
ZZZiying Zhang
Ziying Zhang
Weizhou LiWeizhou Li
Weizhou Li
RYRuixia Yang
Ruixia Yang
XZXiaolian Zhao
Xiaolian Zhao
HZHouan Zhang
Houan Zhang
SK5 steel is the base material used for the preparation of the wrinkle scraper, whose service life strongly affects the working efficiency and economic benefits. In this work, WC–Cr3C2–Ni coating was deposited on the SK5 steel substrate by using High-velocity air fuel spray (HVAF) and Laser cladding (LC) processes respectively, named HVAF-WC coating and LC-WC coating. The microstructure and wear resistance of both coatings were analyzed, and were compared with the substrate sample. Results showed that the coatings were adhesive well onto the substrate. More WC with fine crystals is retained in HVAF-WC coating due to low flame flow temperature, while WC of LC-WC coating is characterized by columnar crystals. The wear rate of HVAF-WC and LC-WC coating was 4.00 × 10−7 mm3/(N•m) and 3.47 × 10−6 mm3/(N•m), respectively, which was two and one orders of magnitude lower than SK5 steel with 3.54 × 10−5 mm3/Nm. HVAF-WC coating exhibited the best wear resistance because of significant fine grain strengthening, which wear mechanism is mainly dominated by abrasive wear. Thus, it was thought that HVAF-WC coating is more effective ways to improve the wear resistance of SK5 steel, comparing with LC-WC coating.

18 April 2023 in Materials
Verified
Journal Article
Open access
PDF file
LMLili Ma
Lili Ma
ZZZaiyang Zhao
Zaiyang Zhao
YWYurong Wu
Yurong Wu
JSJingjing Sun
Jingjing Sun
SGSiyong Gu
Siyong Gu
HZHouan Zhang
Houan Zhang
For investigating the influence mechanism underlying ultrafine Ti(C, N) within micron Ti(C, N)-based cermets, three cermets including diverse ultrafine Ti(C, N) contents were employed. In addition, for the prepared cermets, their sintering process, microstructure, and mechanical properties were systematically studied. According to our findings, adding ultrafine Ti(C, N) primarily affects the densification and shrinkage behavior in the solid-state sintering stage. Additionally, material-phase and microstructure evolution were investigated under the solid-state stage from 800 to 1300 °C. Adding ultrafine Ti(C, N) enhanced the diffusion and dissolution behavior of the secondary carbide (Mo2C, WC, and (Ta, Nb)C) under a lower sintering temperature of 1200 °C. Further, as sintering temperature increased, adding ultrafine Ti(C, N) enhanced heavy element transformation behaviors in the binder phase and accelerated solid-solution (Ti, Me) (C, N) phase formation. When the addition of ultrafine Ti(C, N) reached 40 wt%, the binder phase had increased its liquefying speed. Moreover, the cermet containing 40 wt% ultrafine Ti(C, N) displayed superb mechanical performances.

21 September 2017 in Sensors
Verified
Journal Article
Open access
PDF file
JXJian-De Xie
Jian-De Xie
SGSiyong Gu
Siyong Gu
HZHouan Zhang
Houan Zhang
This work outlines a synthetic strategy inducing the microwave-assisted synthesis of palladium (Pd) nanocrystals on a graphite sphere (GS) and reduced graphene oxide (rGO) supports, forming the Pd catalysts for non-enzymatic glucose oxidation reaction (GOR). The pulse microwave approach takes a short period (i.e., 10 min) to fast synthesize Pd nanocrystals onto a carbon support at 150 °C. The selection of carbon support plays a crucial role in affecting Pd particle size and dispersion uniformity. The robust design of Pd-rGO catalyst electrode displays an enhanced electrocatalytic activity and sensitivity toward GOR. The enhanced performance is mainly attributed to the synergetic effect that combines small crystalline size and two-dimensional conductive support, imparting high accessibility to non-enzymatic GOR. The rGO sheets serve as a conductive scaffold, capable of fast conducting electron. The linear plot of current response versus glucose concentration exhibits good correlations within the range of 1–12 mM. The sensitivity of the Pd-rGO catalyst is significantly enhanced by 3.7 times, as compared to the Pd-GS catalyst. Accordingly, the Pd-rGO catalyst electrode can be considered as a potential candidate for non-enzymatic glucose biosensor.

3 June 2013 in International Journal of Refractory Metals and Hard Materials
Verified
Journal Article
Closed access
HZHouan Zhang
Houan Zhang
SZShuxin Zhuang
Shuxin Zhuang
HWHejian Wu
Hejian Wu
SGSiyong Gu
Siyong Gu
YLYu Lei
Yu Lei

7 June 2026 in Materials
Verified
Journal Article
Open access
PDF file
LMLili Ma
Lili Ma
YXYiping Xu
Yiping Xu
LYLin Yulin
Lin Yulin
Binbin WeiBinbin Wei
Binbin Wei
HZHouan Zhang
Houan Zhang
This study systematically investigated the influence of aluminum nitride (AlN) addition on the microstructure and mechanical properties of Ti(C,N)-based cermets with low Ni/Co and high N contents. The results demonstrate that AlN addition does not alter the phase composition of Ti(C,N)-based cermets, and their microstructure retains the characteristic core–rim morphology. The dissolution of Al atoms from AlN effectively suppressed abnormal growth of Ti(C,N) grains and enhanced the mechanical stability of the binder. Densification and comprehensive mechanical properties strongly depended on the AlN content. Both parameters initially improved with the addition of AlN, peaked at an optimal content of 1.0 wt.%, and then declined upon further addition due to the formation of micropores and brittle agglomerates of Al2O3. At the optimal AlN content of 1.0 wt.%, the cermets demonstrated peak performance: a Vickers hardness of 1676 HV30, a transverse rupture strength of 1486 MPa, and a fracture toughness of 8.8 MPa·m1/2. The results elucidate the dual role of AlN as both a microstructural refiner and a precursor for in situ strengthening of the binder phase.