NICOLA GIANNOTTA

Dr. NICOLA GIANNOTTA

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 July 2023 in Machines
Verified
Journal Article
Open access
PDF file
NGNICOLA GIANNOTTA
NICOLA GIANNOTTA
GSGiada Sala
Giada Sala
Claudio BianchiniClaudio Bianchini
Claudio Bianchini
ATAmbra Torreggiani
Ambra Torreggiani
This paper presents a review of the main advantages and challenges of Additive Manufacturing (AM) applied in the production of soft magnetic components for electrical machines. Firstly, a general introduction about additive manufacturing is made, considering all of its possibilities of application, then the authors focused on the electrical machine application field, in particular the AM of soft ferromagnetic materials. The soft ferromagnetic materials are fundamental for the production of electrical machines, and currently, there are more and more requests for designed ad hoc geometries, which can be difficult to produce with conventional manufacturing technologies. With this purpose, AM can be used to produce the desired geometries.

9 April 2025
Verified
Conference Paper
Closed access
NGNICOLA GIANNOTTA
NICOLA GIANNOTTA
GSGiada Sala
Giada Sala
GPGabriele Puccio
Gabriele Puccio
BKBastian Kallenbach
Bastian Kallenbach
CBClaudio Bianchini
Claudio Bianchini
SNStefano Nuzzo
Stefano Nuzzo
Additive manufacturing is currently being widely investigated in the field of electrical machines. This 3D printing technology can indeed enable complex geometries and reduced material waste, thus potentially overcoming some of the limitations of traditional manufacturing methods. This study focuses on an additively manufactured Fe-Co-V alloy, specifically FeCo49V2, and investigates the impact of a two-stage heat treatment on its magnetic properties. The experimental results underscore the critical role of heat treatment in optimizing the magnetic performance of additively produced FeCo49V2, and appear to demonstrate negligible influence of the build direction.

1 September 2024
Verified
Conference Paper
Closed access
Claudio BianchiniClaudio Bianchini
Claudio Bianchini
NBNicola Bianchi
Nicola Bianchi
GSGiada Sala
Giada Sala
NGNICOLA GIANNOTTA
NICOLA GIANNOTTA
ATAmbra Torreggiani
Ambra Torreggiani
This paper presents an innovative optimized rotor winding for an electrically excited synchronous motor by means of additive manufacturing (AM). The new coil geometry was designed with the purpose of maximizing the filling factor keeping the cross section area of the conductors constant as only constrain in the geometry definition. The proposed solution allow to increase the machine torque density for the same rotor Joule losses or to increase the efficiency of the machine for the same output torque. Then a fluid pole shaping was study to reduce the mechanical stresses in the most critical points taking advantage of the fact that with AM the windings can be design following any kind of theet profile.

1 September 2024
Verified
Conference Paper
Closed access
Claudio BianchiniClaudio Bianchini
Claudio Bianchini
GSGiada Sala
Giada Sala
MFMatteo Frigieri
Matteo Frigieri
MVMattia Vogni
Mattia Vogni
NGNICOLA GIANNOTTA
NICOLA GIANNOTTA
EMElena Macrelli
Elena Macrelli
This paper presents a new extended constant power region control model for interior permanent magnet synchronous machine (IPMSM) powered by a current source inverter (CSI). The IPMSM constant power region is usually obtained with voltage source inverter (VSI) employing flux weakening (FW) and maximum torque per volt (MTPV) control strategy when the voltage at the motor terminal exceed the available DC BUS voltage. This is due to the fact that VSI essentially operates as a step down converter. Even if these control strategy are well know in literature their implementation is always critical, specially when the MTPV is needed. As CSI is intrinsically a step up converter, it is possible to delay FW operation, provided that the voltage applied to the motor does not exceed the voltage rating of the power devices and the limits for the insulation system. So, in order to obtain a wide constant power region, an extend MTPA-FW is here proposed avoiding the need of MTPV and taking the advantage of the step-up intrinsic capability of the CSI.

23 July 2025 in Energies
Verified
Journal Article
Open access
PDF file
GSGiada Sala
Giada Sala
NGNICOLA GIANNOTTA
NICOLA GIANNOTTA
MVMattia Vogni
Mattia Vogni
Claudio BianchiniClaudio Bianchini
Claudio Bianchini
Fabio ImmovilliFabio Immovilli
Fabio Immovilli
This paper presents the analytical model, feasibility assessment, and testing of a novel synchronous reluctance tubular machine, whose mover is manufactured using additive techniques. This approach enables the maximization of the machine’s saliency. The analytical model traditionally used for rotating machines was adapted to match the geometric characteristics of the innovative tubular design proposed in this work. The analytical results were validated through 2D finite element analysis (FEA). Subsequently, several mock-ups were 3D-printed using iron metal powder to evaluate the manufacturing feasibility of the proposed machine. Finally, the machine was tested to verify the accuracy of the analytical model.

1 September 2024
Verified
Conference Paper
Closed access
Claudio BianchiniClaudio Bianchini
Claudio Bianchini
ATAmbra Torreggiani
Ambra Torreggiani
GSGiada Sala
Giada Sala
ASAndrea Sala
Andrea Sala
NGNICOLA GIANNOTTA
NICOLA GIANNOTTA
MDMatteo Davoli
Matteo Davoli
Diagnostic and prognostic became key activities in industry 4.0. This paper presents the design and validation of a low-cost and self-powered sensor for condition monitoring of a mechanical speed variator. This sensor can be easily coupled with commercial sin/cos sensors and used to plan a predictive maintenance policy. Specifically to the speed variator, thanks to the two sin/cos sensors mounted on the two shafts, the elasto-plastic deformation of the entire kinematic system can be estimated and predictive maintenance can be scheduled.