Ting Yuan

Ms. Ting Yuan


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2020 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
ZYzhipeng yuan
zhipeng yuan
YTyiyou tu
yiyou tu
TYTing Yuan
Ting Yuan
YHYaohua Huang
Yaohua Huang
YZYunhe Zhang
Yunhe Zhang

29 July 2019 in Metals
Verified
Journal Article
Open access
PDF file
TYTing Yuan
Ting Yuan
JJJinghua Jiang
Jinghua Jiang
YWYuna Wu
Yuna Wu
ZYZhipeng Yuan
Zhipeng Yuan
AMAibin Ma
Aibin Ma
YYYuchun Yuan
Yuchun Yuan
This paper investigated the cooperative effects of Li addition and warm Equal Channel Angular Pressing (ECAP) on improving the mechanical properties of an Al-Mg-Li alloy for further weight reduction. The results showed that more Li addition could obviously refine the grains of the as-cast alloy and reduce its density value to only 2.37 g/cm3 when Li content reached 2.5% (about 12.6% lighter than commercial Al alloys). It also had a pronounced influence on the precipitations in the Al-5.5Mg-xLi-0.1Zr alloy, i.e., the number density and size of Al2MgLi and δ’-Al3Li phases. The yield strength of the as-cast alloy was increased with increasing Li, but the elongation deteriorated due to primary network intergranular Al2MgLi and more δ’ particles in the high Li-containing alloy. The warm multi-pass ECAP process was found to simultaneously improve the strength and ductility of the Al-Mg-Li alloys, and greatly alleviate the detrimental effect of Li addition on the elongation, thereby making the ultrafine-grained (UFG) alloys, a good combination of lightweight and high performance, very attractive for aerospace applications for much higher specific strength than both Al matrix composites and Mg alloys.

6 November 2017 in Anti-Corrosion Methods and Materials
Verified
Journal Article
Closed access
TYTing Yuan
Ting Yuan
MZMin-Da Zhang
Min-Da Zhang
JNJia-Hui Ni
Jia-Hui Ni
YCYa-Xuan Chen
Ya-Xuan Chen
FGFei Geng
Fei Geng
Purpose: The purpose of this paper is to compare corrosion behavior of a modified multilayer material with Cu before and after brazing process. Design/methodology/approach: Sea water acidified accelerated tests (SWAATs), potentiodynamic polarization tests and scanning electron microscopy were used to study the corrosion behavior and macro/micro structures. Results indicate that the corrosion mechanisms of the sheets before and after brazing process are completely different. Findings: The un-brazed material is uniform corrosion, while the brazed material has a high sensitivity to localized corrosion and loses cathodic protection to the core. It is found that brazing process causes copper transition from the core alloy into eutectic phases in the cladding, leading to higher Ecorr and different potential distribution compared with those of un-brazed materials. Originality/value: For the modified multilayer material after brazing, there are two stages of corrosion. First, corrosion attack takes place along eutectic phases in the cladding material, and then core alloy dissolves by forming a galvanic couple with the nobler residual cladding.

25 September 2025 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
CHChengcheng Han
Chengcheng Han
YHYitong Hu
Yitong Hu
HHHao Huang
Hao Huang
TYTing Yuan
Ting Yuan
HLHuan Liu
Huan Liu
YWYuna Wu
Yuna Wu

22 August 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
YWYuna Wu
Yuna Wu
HDHongchen Dong
Hongchen Dong
HHHao Huang
Hao Huang
TYTing Yuan
Ting Yuan
Jing BaiJing Bai
Jing Bai
AMAibin Ma
Aibin Ma
7046 aluminum alloy has good fatigue property, corrosion resistance and weld property, but the moderate strength and plasticity limit its wider application and development. In the present study, severe plastic deformation (SPD) was applied prior to T6 treatment to significantly strengthen and toughen the 7046 aluminum alloy. Results indicate that the alloy processed by 4 passes of equal channel angular pressing (ECAP) at 300 ℃ prior to T6 treatment exhibits an excellent mechanical performance, with ultimate tensile strength (UTS) and elongation (EL) of 485 MPa and 19%, exhibiting an improvement of 18.6% and 375% compared to that of the T6 alloy, respectively. The mechanical properties of the alloy are further improved by the additional room temperature (RT) rolling process, with UTS of 508 MPa and EL of 23.4%. There are more precipitates of η' and Al6Mn phases in the 300℃4P-R80%-T6 and 300°C4P-T6 alloys, which contribute to the strengthening and toughening enhancement by SPD processed T6 alloy. The results of this work may shed some light on enhancing 7046 aluminum alloy.