Room-temperature gas sensors based on granulated carbon nanofiber material were investigated for the detection of NO2. The granulated material consisting of intertwined carbon nanofibers was synthesized by the decomposition of CH4 over the Ni/Al2O3 catalyst in a vibro-fluidized bed reactor. Carbon material was investigated using transmission electron microscopy, Raman spectroscopy, low-temperature nitrogen adsorption, and X-ray photoelectron spectroscopy. Investigation of the gas sensors towards NO2 at room temperature (25 ± 2 °C) was carried out in a dynamic flow-through setup in the range from 1 to 500 ppm. A comparison of the sensitivity gas sensor to NH3 and CH4 was also given. The sensor based on non-treated carbon nanofiber material showed the response ΔR/R0 of 5.1 % to 10 ppm of NO2. It was found that the sensor response to NO2 decreased when increasing the relative humidity. The effect of the relative humidity was more pronounced for low concentrations of nitrogen dioxide and decreases with a further increase in them.
Highly porous expanded graphite was synthesized by the programmable heating technique using heating with a constant rate (20 °C/min) from room temperature to 400–700 °C. The samples obtained were analyzed by scanning electron microscopy, energy-dispersive spectroscopy, low-temperature nitrogen adsorption, X-ray photoelectron spectroscopy, Raman spectroscopy, thermogravimetry, and differential scanning calorimetry. A comparison between programmable heating and thermal shock as methods of producing expanded graphite showed efficiency of the first one at a temperature 400 °C, and the surface area reached 699 and 184 m2/g, respectively. The proposed technique made it possible to obtain a relatively higher yield of expanded graphite (78–90%) from intercalated graphite. The experiments showed the advantages of programmable heating in terms of its flexibility and the possibility to manage the textural properties, yield, disorder degree, and bulk density of expanded graphite.
The synthesis of a 90% Ni/Al2O3 catalyst via solution combustion synthesis with various fuels was studied in this work. Catalysts with a high content of the active component (i.e., nickel) were obtained as a result of the combustion of Ni(NO3)2·6H2O and Al(NO3)3·9H2O mixtures with fuel. The fuels, such as hexamethylenetetramine, glycine, urea, starch, citric acid, and oxalic acid, were investigated. The synthesis was carried out in a furnace, with the temperature being raised from room temperature to 450 °C at a rate of 1 °C per min. The paper evaluates the efficiency of fuels and their effect on the structure and properties of catalysts, as well as their catalytic activity. The catalyst was used for the synthesis of hydrogen and carbon nanofibers by methane decomposition at 1 bar and 550 °C. The catalysts were tested in a vertical flow reactor without preliminary reduction. The obtained samples of catalysts and carbon nanomaterials were studied by transmission electron microscopy, low-temperature nitrogen adsorption, and X-ray diffraction. The highest activity of the catalyst was obtained when citric acid was used as a fuel. The specific yields of hydrogen and carbon nanofibers were 17.1 mol/gcat and 171.3 g/gcat, respectively. Catalytic decomposition of methane led to the formation of cup-stacked carbon nanofibers.
The parameters of the synthesis of catalysts by the solution combustion method using oxalic acid as a reducing agent were investigated. The activity of the catalysts was determined in the production of hydrogen and carbon nanofibers by the catalytic decomposition of methane. The efficiency of oxalic acid was demonstrated in the preparation of a nickel catalyst (90% Ni/10% Al2O3), which does not require the preliminary reduction with hydrogen. Regression analysis identified that the yields of carbon and hydrogen are most strongly affected by temperature among other synthesis parameters.
1 November 2018 in Russian Journal of Applied Chemistry
A promising method based on solution combustion was considered for preparing a catalyst for the synthesis of nanofibrous carbon and hydrogen. The temperature profile of the hexamethylenetetramine...
In this work, general purpose rubber composites were created based on a mixture of non-polar cis-1,4-isoprene rubber and cis-1,4-divinyl rubber as components. The main filler used was carbon black, while various graphite-like materials (graphite oxide, reduced graphite oxide, expanded graphite, and graphite nanoplatelets) served as additives. It was determined that the addition of these graphite-like materials resulted in a reduction in Mooney viscosity, with the introduction of graphene nanoplatelets having the most significant effect, contributing to a viscosity decrease of 8.5%. The relaxation rate increased, positively impacting elastic recovery and consequently reducing shrinkage. The introduction of graphite oxide, graphite nanoplatelets, and expanded graphite also increased the time to the onset of the vulcanization reaction; moreover, these additives lengthened the time needed to reach the optimum level of vulcanization. The addition of various graphite-like materials significantly affected the elongation at break, with the highest increase attributable to the addition of expanded graphite and reduced graphite oxide. It was found that the conditional tensile strength of these additives had little effect. Upon assessing the elastic-strength properties after aging, it was found that the inclusion of graphite-like materials reduced the elongation at break.