Wang Zhen Ming

Mr. Wang Zhen Ming

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2022 in Welding in the World
Verified
Journal Article
Closed access
PDF file
SMShazia Muzaffer
Shazia Muzaffer
KCkyongho chang
kyongho chang
WMWang Zhen Ming
Wang Zhen Ming
SKSeong-Uk Kang
Seong-Uk Kang

1 January 2013
Verified
Book Chapter
Closed access
WMWang Zhen Ming
Wang Zhen Ming
JCJames C. Cobb
James C. Cobb
RCRandel Tom Cox
Randel Tom Cox
MTMartitia P. Tuttle
Martitia P. Tuttle
OBOliver S. Boyd
Oliver S. Boyd
JLJacques Locat
Jacques Locat
Scientific understanding of earthquakes in the New Madrid seismic zone has advanced greatly in recent years, but these advances have resulted in neither better assessment of seismic hazard and risk nor better mitigation policy. The main reasons for this are (1) misunderstanding about the National Seismic Hazard Maps and (2) confusion about seismic hazard and risk. Seismic hazard and seismic risk are two fundamentally different concepts, even though they have often been used interchangeably. Both are used differently in policy decision making, but seismic risk is the deciding factor, not seismic hazard. Even though the input parameters are scientifically sound, we contend that the National Seismic Hazard Maps produced for the New Madrid region are flawed because they were produced from probabilistic seismic hazard analysis (PSHA). PSHA is scientifically flawed: As a complex computer model, it could not pass a simple sensitivity test with a single input earthquake, and the annual probability of exceedance (i.e., exceedance probability in one year and a dimensionless quantity) has been erroneously interpreted and used as the annual frequency or rate of exceedance (i.e., the number of event exceedances per year and a dimensional quantity). Thus, the seismic hazard and resulting seismic risk estimates from PSHA can be viewed as artifacts, and the mitigation policies developed, the NEHRP (National Earthquake Hazards Reduction Program) provisions and resulting building codes in particular, are problematic. Scenario seismic hazard analysis is a more appropriate approach for seismic hazard assessment, seismic risk assessment, as well as policy development in the New Madrid region.

30 December 2020 in Journal of Welding and Joining
Verified
Journal Article
Open access
PDF file
WMWang Zhen Ming
Wang Zhen Ming
KCkyongho chang
kyongho chang
SMShazia Muzaffer
Shazia Muzaffer
1) The fatigue life of butt-welded members results obtained by fatigue FEM, the HSS method, and experiments were compared.

3 October 2024 in International Journal of Steel Structures
Verified
Journal Article
Closed access
PDF file
WMWang Zhen Ming
Wang Zhen Ming
KCkyongho chang
kyongho chang
MHMikihito Hirohata
Mikihito Hirohata

24 April 2023 in Processes
Verified
Journal Article
Open access
PDF file
WMWang Zhen Ming
Wang Zhen Ming
KCkyongho chang
kyongho chang
SMShazia Muzaffer
Shazia Muzaffer
MHMikihito Hirohata
Mikihito Hirohata
The construction of new renewable energy infrastructures and the development of new ocean resources continues to proceed apace. In this regard, the increasing size and capacity of offshore wind turbines demands that the size of their accompanying supporting marine structures likewise increase. The types of marine structures utilized for these offshore applications include gravity base, monopile, jacket, and tripod structures. Of these four types, monopile structures are widely used, given that they are comparatively easy to construct and more economical than other structures. However, constant exposure to harsh cyclic environmental loads can cause material deterioration or the initiation of fatigue cracks, which can then lead to catastrophic failures. In this paper, a 3D fatigue finite element analysis was performed to predict both the fatigue life and the crack initiation of a welded monopile substructure. The whole analysis was undertaken in three steps. First, a 3D non-steady heat conduction analysis was used to calculate the thermal history. Second, a thermal load was induced, as an input in 3D elastoplastic analysis, in order to determine welding residual stresses and welding deformation. Finally, the plastic strain and residual stress were used as inputs in a 3D fatigue FE analysis in order to calculate fatigue crack initiation and fatigue life. The 3D fatigue finite element analysis was based on continuum damage mechanics (CDM) and elastoplastic constitutive equations. The results obtained from the 3D fatigue finite element analysis were compared with hot spot stresses and Det Norske Veritas (DNV-GL) standards.

1 September 2023 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
YMYutian Ma
Yutian Ma
WMWang Zhen Ming
Wang Zhen Ming
XTXingchang Tang
Xingchang Tang
GCGanghu Cheng
Ganghu Cheng
YLYa-Jun Liu
Ya-Jun Liu
JLJunzhao Liu
Junzhao Liu
This study reports the fabrication of FeCoCrNiMn high-entropy alloy using high-purity powders of Fe, Co, Cr, Ni, and Mn through the processes of mechanical alloying (MA) and spark plasma sintering (SPS). We systematically investigated the effects of different ball milling times (10 h, 20 h, 30 h, 40 h, 50 h) and sintering temperatures (700°C, 800°C, 900°C, 1000°C, 1100°C) on the structure and capabilities of the alloy. The findings indicate that the atomic proportion of Fe:Co:Cr:Ni:Mn approach 1:1:1:1:1. The distribution of all elements is basically uniform, but the Cr element is slightly biased in the structure after 40 h ball milling. The voids in the structure are gradually decreasing as temperatures rise. The matrix structure is mainly composed of a white FCC matrix phase and a gray Cr-rich σ phase. The alloy structure is the densest. It has the highest density of 7.060 g/cm3, the highest compressive strength of 1480 MPa, and a plastic deformation of 13% when the SPS temperature reaches 1000°C. The FeCoCrNiMn high-entropy alloy is prepared by a ball milling time of 40 h, and spark plasma sintering of 1000°C has the best comprehensive properties.