kyongho chang

Prof. Dr. kyongho chang


Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2015 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
HSHyun-Seop Shin
Hyun-Seop Shin
KPKi-Tae Park
Ki-Tae Park
CLChin-Hyung Lee
Chin-Hyung Lee
KCkyongho chang
kyongho chang
VDVuong Nguyen Van Do
Vuong Nguyen Van Do
Influence of welding process and welding consumable on the impact toughness at low temperatures of the Heat Affected Zone (HAZ) and the weld metal in a structural steel weldment was investigated. A comparison of the low temperature impact toughness was made between the welded joints fabricated by Shielded Metal Arc Welding (SMAW) and Flux Cored Arc Welding (FCAW) processes, respectively. The Charpy impact tests along with the microstructural observations and the hardness measurements were carried out to derive the effective welding method to guarantee the higher impact toughness of the HAZ and the weld metal at low temperatures. Standard V-notch Charpy impact specimens were prepared and tested under dynamic loading condition. Variation of the Charpy impact energy with respect to the test temperature and that of the hardness across the welds were presented and correlated with the microstructure and the welding process. Analysis of the results unveiled that the weld metal of the FCAW joint has a little higher low temperature impact toughness owing to the higher nickel content, whilst the HAZ of the SMAW joint has much superior impact toughness at low temperatures attributed to the lower heat input; thus the efficient welding method to ensure higher low temperature impact toughness of the HAZ and the weld metal is to employ a low heat input welding process using a welding consumable with high nickel content.

1 November 2012 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
HPHyun-Chan Park
Hyun-Chan Park
CLChin-Hyung Lee
Chin-Hyung Lee
KCkyongho chang
kyongho chang
In recent years, the replacement repair welding has been suggested as a repair method for damaged steel bridges. The distinguished feature of the method is that it can be carried out without incurring traffic dislocation. However, the method has not ever been attempted because of its lack of certainty for safety, i.e., repair method by welding inevitably involves cutting and welding processes, and the safety during these processes has not been established yet. This paper describes the strengthening of a damaged steel girder bridge through the replacement repair welding. Field load test was conducted both during and after the replacement repair welding, and the response of the bridge to test vehicle loading was recorded. Results of the field test are reported, and the validity of the replacement repair welding during in-service loading is identified.

28 December 2023 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
SMShazia Muzaffer
Shazia Muzaffer
KCkyongho chang
kyongho chang
MHMikihito Hirohata
Mikihito Hirohata
In a wind energy system, the safety and stability of substructures plays an important role during the in service of offshore structure. Offshore structures are continuously subjected to high cyclic fatigue loads and may experience fatigue cracks due to the continuous accumulation of plastic strain and stress concentrations at welded joints. The fatigue life of welded tubular joints is one of the most important factors determining the life of offshore structures. In this study, the fatigue analysis of tubular joints of the tripod and jacket support structure was performed using 3D fatigue FEM to estimate the fatigue life and predict the positions of crack initiation. The 3D fatigue FE is based on constitutive equations and continuum damage mechanics. The welding state of tubular joints were reproduced to calculate the welding residual stresses and welding deformation. The residual stresses and weld deformation were used as input together with cyclic loading in the 3D fatigue FE to calculate the fatigue life and predict the crack initiation positions. The S-N curve calculated by the 3D fatigue FE analysis were compared with the SN curves of Eurocode 3. The results show that 3D fatigue FE analysis is an effective tool to analyze large and complex structures before installation to ensure the safety and stability of the structure.

1 August 2007 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
CLChin-Hyung Lee
Chin-Hyung Lee
KCkyongho chang
kyongho chang

21 February 2022 in Welding in the World
Verified
Journal Article
Closed access
PDF file
SMShazia Muzaffer
Shazia Muzaffer
KCkyongho chang
kyongho chang
WMWang Zhen Ming
Wang Zhen Ming
SKSeong-Uk Kang
Seong-Uk Kang

21 January 2019 in Archive of Applied Mechanics
Verified
Journal Article
Closed access
PDF file
KCkyongho chang
kyongho chang
SKSeong-Uk Kang
Seong-Uk Kang
ZWZhen-Ming Wang
Zhen-Ming Wang
SMShazia Muzaffer
Shazia Muzaffer
MHMikihito Hirohata
Mikihito Hirohata