Periprosthetic joint infections (PJI) are a common reason for orthopedic revision surgeries. It has been shown that the silver surface modification of a titanium alloy (Ti–6Al–4V) by PMEDM (powder mixed electrical discharge machining) exhibits an antibacterial effect on Staphylococcus spp. adhesion. Whether the thickness of the silver-modified surface influences the adhesion and proliferation of bacteria as well as the ossification processes and in-vivo antibacterial capacity has not been investigated before. Therefore, the aim of this work is to investigate the antibacterial effect as well as the in vitro ossification process depending on the thickness of PMEDM silver modified surfaces.
The detection and differentiation of BCP and CPP crystals in calcified tissue is an important factor in the context of research and potential future treatment of osteoarthritis and chondrocalcinosis. Current standard methods originate from clinical practice and often lack precision in the correct identification of the calcium crystal type. In this work, a step-by-step guide for the use of the high-resolution imaging methods of tissue sections, Raman spectroscopy and scanning electron microscopy (SEM) in combination with energy-dispersive X-ray spectroscopy (EDS), for calcium crystal identification is presented. Sample preparation including Von Kossa staining, measurement and measurement parameters, data processing and data analysis methods are discussed and described. Furthermore, the different methods are compared to show advantages and disadvantages. Overall, Raman spectroscopy is a reasonable method from an economic point of view and regarding the time/effort required for acquiring highly reliable data in calcium crystal identification. Potentially, semi-quantitative results can be obtained with little effort and without the destruction of the respective test sample. The analysis/penetration depth during the Raman measurements, which is not precisely defined, poses a potential problem for accuracy. SEM can also be used for this task but requires more time, advanced technical knowledge and a pre-treatment of the samples using, e.g., gold sputtering, which may distort further analysis on the specific specimen. Therefore, this technique yields additional value compared to Raman spectroscopy only with additional research questions needed to be answered in the same sample, such as analysis of the sample topography or analysis of other unknown particles/deposits using EDS. The methods described in this manuscript are helpful for retrospective analyses in the context of research, but can also be used for potential future treatment strategies to discriminate between osteoarthritis and chondrocalcinosis patients.
Ectopic articular calcification is a common phenomenon of osteoarthritic joints, and closely related with disease progression. Identification of the involved calcium crystal types represents an important topic in research and clinical practice. Difficulties in accurate detection and crystal type identification have led to inconsistent data on the prevalence and spatial distribution of BCP and CPP deposition. Combining multiple imaging methods including conventional radiography, histology and Raman spectroscopy, this study provides a comprehensive analysis of BCP and CPP based calcification, its frequency and distribution in cartilage and synovial membrane samples of 92 OA patients undergoing knee replacement surgery. Conventional radiography showed calcifications in 35% of patients. Von Kossa staining detected calcified deposits in 88% and 57% of cartilage and synovial samples, respectively. BCP crystals presented as brittle deposits on top of the cartilage surface or embedded in synovial tissue. CPP deposits appeared as larger granular needle-shaped clusters or dense circular pockets below the cartilage surface or within synovial tissue. Spectroscopic analysis detected BCP crystals in 75% of cartilage and 43% of synovial samples. CPP deposition was only detected in 18% of cartilage and 15% of synovial samples, often coinciding with BCP deposits. BCP is the predominant crystal type in calcified cartilage and synovium while CPP deposition is rare, often coinciding with BCP. Distinct and qualitative information on BCP and CPP deposits in joint tissues give rise to the speculation that different disease entities are involved that might need different treatment strategies.
This study compares CoCrMo particles generated by a high-energy ball milling method with those produced by the established Buchhorn method and with in vivo-generated wear particles from periprosthetic tissue. CoCrMo particles were produced utilization both methods. The particle size distribution was analyzed using laser diffraction, and the morphology was examined through scanning electron microscopy (SEM). Energy-dispersive X-ray spectroscopy (EDS) provided a qualitative analysis of the material composition. The high-energy ball milling method yielded CoCrMo particles with a D50 of 7.92 µm, a significantly smaller value than the D50 of 88.30 µm observed for Buchhorn particles. The SEM analysis demonstrated that the particles produced by the ball mill have a roundish, red blood cell-like and irregular shape, similar to that observed in particles generated in vivo. In contrast, the particles produced by the Buchhorn method exhibited a flake-like and irregular morphology. The ball mill particles displayed a tendency towards agglomeration, which was also observed in particles generated in vivo. In conclusion, the ball mill method produces CoCrMo particles that closely resemble natural wear particles in terms of size and morphology. These particles provide a superior model for biological testing in comparison to those produced by the Buchhorn method. Furthermore, the ball mill method offers advantages in terms of reproducibility and scalability, making it a promising alternative for the generation of CoCrMo particles for orthopedic research.