Recently, the diameters and construction water depths of the pile foundations of planned and newly built sea-crossing bridges have been increasing greatly. Hydrodynamic loads are the key control factors in the design of super-large-diameter piles. However, most of the previous studies focused on the inline force on the pile with a small diameter, and there were few cases to consider the impact of the transverse force on the hydrodynamic load of the pile under wave-current actions. In this study, to understand the hydrodynamic loads on such deep-water super-large-diameter piles, the prototype was one of the 6.3-m piles used in the Xihoumen Rail-cum-Road Bridge, and 1:60-scale model tests were carried out in an experimental tank, with the actions of regular waves and waves combined with currents used as loads. The influence of the current velocity and static wave height on the inline and transverse forces on the pile was measured and analyzed. The experimental results indicate that with increasing current velocity, the fluctuation characteristics of the wave-current-induced inline and transverse forces change significantly, and their peak values increase obviously compared to those induced by only waves. In particular, the peak transverse force increases tens of times and can become equivalent to the inline force. The modified Morison formula and Kutta–Joukowski formula are used to derive the correlations between the drag coefficient CD, inertia coefficient CM, lift coefficient CL, and redefined Keulegan–Carpenter number KC*. Under wave-current action, the transverse force contributes quite significantly to the hydrodynamic load on a super-large-diameter pile, making it easier to trigger extreme structural loads. The results presented herein are an important reference for the engineering designs of such super-large-diameter piles.
In the construction of large‐tonnage box girder, the construction load of box girder transport is generally greater than the operating load in highway industry; therefore, it is a crucial task to carry out accurate simulation and optimization on bearing box girder. For this purpose, the refined modeling method of 40 m/1270t box girder is studied first in this paper, followed by detailed stress analysis by considering the impact coefficient of vehicles and the most unfavorable conditions. Tracking tests on dead load, prestressed load, and the transport load have shown that the calculated stress values obtained by the refined models are very close to the measured stress values. Based on dynamic strain test of the vehicles at the speed of 4 km/h, the impact coefficient of four vehicles is estimated to be 1.08 and its value meets the requirements of no more than 1.1 provided by the vehicle manufacturer. Aimed at no tensile stress in the midspan section, the optimized geometry of 40 m box girder is obtained with less concrete and longitudinal prestressed tendons. These results demonstrate the plausibility and validity of the proposed research methods and optimization schemes for large‐tonnage box girder transport.
To study the mechanical characteristics of complex pile-cap foundations and the distribution law of hydrodynamic pressure acting on piles and cap in deep-water environments, the 60m deep-water pile-cap foundation of Xihoumen rail-cum-road bridge was considered for this investigation. This paper focused on introducing the design and implementation process of simulating an earthquake using an underwater shaking-table test for a 1:60 complex pile-cap foundation model and systematically summarizing the test results. The test results showed that water reduced the acceleration of complex pile-cap foundation; however, the strain, displacement, and hydrodynamic pressure increased in varying degrees with water depths, and the maximum strain of the piles increased by 13.8 for the X-direction earthquake excitation and 15.1 for the Y-direction earthquake excitation in 1.0m water-depth environment. The strain of the corner pile was the largest under earthquake excitation, followed by that of the front-row pile, and the strain of the middle pile was the smallest. When the water depth was 1.0m, the maximum strain difference of each pile in the X- and Y-directions reached 26.4 and 27.5, respectively. The hydrodynamic pressure acting on the piles decreased gradually from bottom to top, the edge pile bore more hydrodynamic pressure than the middle pile, and the hydrodynamic pressure difference between the piles reached 20. Owing to the influence of the round-ended cap, the hydrodynamic pressure suddenly increased at the cap position, and the distribution law of the cap showed a gradually declining trend from front to side; however, the attenuation amplitude was affected by its shape.