The dynamic constitutive behaviors of concrete-like materials are of vital importance for structure designing under impact loading conditions. This study proposes a new method to evaluate the constitutive behaviors of ordinary concrete at high strain rates. The proposed method combines the Lagrangian-inverse analysis method with optical techniques (ultra-high-speed camera and digital image correlation techniques). The proposed method is validated against finite-element simulation. Spalling tests were conducted on concretes where optical techniques were employed to obtain the high-frequency spatial and temporal displacement data. We then obtained stress–strain curves of concrete by applying the proposed method on the results of spalling tests. The results show non-linear constitutive behaviors in these stress–strain curves. These non-linear constitutive behaviors can be possibly explained by local heterogeneity of concrete. The proposed method provides an alternative mean to access the dynamic constitutive behaviors which can help future structure designing of concrete-like materials.
Explosively driven fragmentation of ductile metals cylinders is a highly complex phenomenon. In this work, the fracture characteristics of exploded TA2 titanium alloy cylinder with varied charge were investigated numerically and experimentally. The results show that the fracture surfaces of fragments lie along planes of maximum shear stress for either a higher or a lower detonation pressure, but their mechanism is different. The finite element analysis demonstrated that the equivalent plastic strain in the middle of the wall is always larger than that of inner and outer wall for metal cylinder during the stage of shock wave driven period. For the high explosive pressures, the micro-cracks originated firstly in middle zone of wall during the stage of shock wave driven, and extend to the inner and outer wall in the direction of maximum shear stress. Explosives which generate lower detonation pressures, the shear fracture of cylinder originated from the inner wall and propagate to the outer wall in an angle of 45° or 135° to radial, the crack begin at the stage of free expansion. The simulated analysis of the process of deformation and fragmentation for exploded metal cylinder agree with the experimental results.
To study the mechanical characteristics of complex pile-cap foundations and the distribution law of hydrodynamic pressure acting on piles and cap in deep-water environments, the 60m deep-water pile-cap foundation of Xihoumen rail-cum-road bridge was considered for this investigation. This paper focused on introducing the design and implementation process of simulating an earthquake using an underwater shaking-table test for a 1:60 complex pile-cap foundation model and systematically summarizing the test results. The test results showed that water reduced the acceleration of complex pile-cap foundation; however, the strain, displacement, and hydrodynamic pressure increased in varying degrees with water depths, and the maximum strain of the piles increased by 13.8 for the X-direction earthquake excitation and 15.1 for the Y-direction earthquake excitation in 1.0m water-depth environment. The strain of the corner pile was the largest under earthquake excitation, followed by that of the front-row pile, and the strain of the middle pile was the smallest. When the water depth was 1.0m, the maximum strain difference of each pile in the X- and Y-directions reached 26.4 and 27.5, respectively. The hydrodynamic pressure acting on the piles decreased gradually from bottom to top, the edge pile bore more hydrodynamic pressure than the middle pile, and the hydrodynamic pressure difference between the piles reached 20. Owing to the influence of the round-ended cap, the hydrodynamic pressure suddenly increased at the cap position, and the distribution law of the cap showed a gradually declining trend from front to side; however, the attenuation amplitude was affected by its shape.
Obtaining reliable dynamic mechanical properties through experiments is essential for developing and validating constitutive models in material selection and structural design. This study introduces a dynamic tensile method using a modified M-type specimen loaded by a split Hopkinson pressure bar (SHPB). A closed M-type specimen was thus employed. Finite element simulations and experiments were used to validate the design of the M-type specimen, which was fabricated using 17-4PH (precipitation hardening) stainless steel powder with a 3D (three-dimensional) selected laser melting (SLM) printer. After verifying force balance and uniform deformation in the tensile region, tensile tests were conducted across strain rates from quasi-static to a strain rate of 5900 s−1. The results demonstrated that this method effectively assessed the dynamic tensile behaviors of stainless steel at high strain rates, and achieved both ultra-high strain rates and large plastic deformation.