The mechanical efficiency of soil stabilization with cement is mainly controlled by various parameters, namely, the amount of binder, the compaction soil state and the curing conditions. The strength of the treated soil is the result of a complex combination of several factors that condition the physicochemical processes involved in cement hydration, which are difficult to monitor. The objective of this study is to identify the relevant parameters governing the bonding in cement-treated soil and suggest a predictive model for strength evolution using these parameters as input. To this purpose, an extensive testing program is presented to assess the impact of the initial water content (11–18%) and dry density (1.6–1.87 Mg/m3) as well as cement dosage (3 and 6%) in sealed curing conditions for 0, 7, 28 and 90 days. The water content variation, the total suction and the compressive strength were measured after different curing durations. The experimental results are first discussed in the parameters’ space, and then through a principal components analysis to overcome the complexity due to the parameters’ interdependency. The PCA revealed that the cement dosage explained 40% of the dataset variance, the remaining 60% being related to a combination of the initial state and curing time. Finally, a predictive model based on an artificial neural network was developed and tested. The predicted results were excellent, with an R2 of +0.99 with the training data and +0.93 with the testing data. These results should be improved by extending the dataset to include different soils and additional compaction conditions.
Artificial ground freezing (AGF) has emerged as a prominent treatment method due to its ability to mechanically strengthen the soil while reducing its permeability. However, its implementation has raised concerns about its impact, particularly with respect to frost heave and subsequent thaw-induced displacements. These soil movements can cause subsidence and pose a significant threat to the integrity of surface structures. Overburden pressure plays a crucial role in AGF and determines the amount of heave generated. This paper presents an analysis of the existing literature about soil freezing and thawing. The aim is to offer an understanding of these processes, specifically with regard to their application in AGF. This paper explains the behavior of soil during freezing, with particular emphasis on the influence of overburden pressure. It also investigates frozen soils’ thawing and freeze–thaw (FT) cycles’ long-term effects on soil properties. AGF offers improved soil strength and reduced water permeability, enhancing construction project stability. However, the interplay between the temperature, soil composition, and initial ground conditions during freezing is complex. This thermo-hydro-chemo-mechanical process strengthens the soil and reduces its permeability, but it can also induce frost heave due to water expansion and ice lens formation. Overburden pressure from the overlying soil limits ice lens growth. FT cycles significantly impact soil properties. In fine-grained soils, FT cycles can lead to over-consolidation, while rapid thawing can generate high pore pressures and compromise stability. Importantly, FT acts as a weathering mechanism, influencing soil properties at both the microscopic and macroscopic scales. These cycles can loosen over-consolidated soil, densify normally consolidated soil, and increase overall hydraulic conductivity due to structural changes. They can also weaken the soil’s structure and deteriorate its mechanical performance.
International audienceCet article rapporte un ensemble de résultats d'études expérimentales effectuées sur un matériau gonflant naturel. Dans un premier temps, un essai de porosimétrie au mercure a mis en évidence la double structure du sol étudié: la micro- et la macrostructure. Afin d'obtenir la courbe de rétention d'eau, deux méthodes d'imposition de succion ont été appliquées: la méthode osmotique pour les succions inférieures à 8,5 MPa et la méthode de solutions salines pour les succions supérieures à 8,5 MPa. Des essais œdomètriques ont également été effectués avec imposition de succion par la méthode osmotique. Plusieurs cycles de séchage―humidification entre 0 et 2 MPa ont été appliqués sur des éprouvettes sous trois faibles charges mécaniques constantes (20, 40 et 60 kPa). Pendant ces cycles, ces éprouvettes présentent un gonflement cumulé. Les résultats montrent que les déformations volumiques convergeant vers un état d'équilibre où le sol présente un comportement réversible. L'ensemble de ces résultats a permis d'obtenir les paramètres du modèle élastoplastique (BExM). Ce modèle implanté dans un code de calcul aux éléments finis (Code_Bright) est utilisé pour l'étude du comportement hydromécanique de ce sol naturel chargé par une semelle filante. L'objectif de cette étude est d'analyser l'influence des sollicitations hydriques sur les déplacements de cette fondation. Le modèle est capable d'aboutir à des résultats représentatifs de ce type de chargement hydromécanique complex