One-dimensional (1D) SnO2 nanostructures, as n-type semiconductors with a wide band gap, exhibit unique photoelectric properties that offer potential applications in electronic, photoelectric, gas sensing, and energy generation devices. A detailed study of template-free reaction systems is essential to regulate and efficiently synthesise 1DSnO2 nanostructures. This study employed the hydrothermal method to prepare 1DSnO2 nanostructures, with SnCl4·5H2O as the tin source. The impact of various experimental conditions on SnO2 morphology is analysed. Here, 1DSnO2 nanostructures were characterised by analytical methods such as X-ray powder diffraction, transmission electron microscopy, scanning electron microscopy, and field emission double-beam electron microscopy. The results confirmed the formation of 1DSnO2 nanostructures with a mixed morphology of nanorods and nanowires. The nanorods exhibited a length of 422.87 ± 110.15 nm, a width of 81.4 ± 16.75 nm, and an aspect ratio of 5:1, whereas the nanowires displayed a length of 200 ± 45.24 nm, a width of 15 ± 5.62 nm, and an aspect ratio of 13:1. With the addition of 50 mg of polyvinylpyrrolidone and seed crystal, the acquisition time of the 1DSnO2 nanostructures decreased from 48 to 12 h. The 1DSnO2 nanostructures were efficiently obtained without a template, laying the foundation for large-scale production and application.
22 October 2017 in IOP Conference Series: Materials Science and Engineering
The purpose of this study is to investigate the effects of semi-angle and platinum tube wall thicknesses on the first-step drawing process of platinum-clad nickel bars using finite element simulation. Three different semi-angles of die (3°, 5°, 7°) and three different platinum tube wall thicknesses (0.275 mm, 0.3 mm, 0.325 mm) were selected in the study. The effects of semi-angle and platinum tube wall thicknesses on drawing force, equivalent stress, cladding behavior and damage coefficients during the first-step drawing process were discussed in detail. The simulated results of cladding condition and damage obtained from Deform 3D V11 software are validated with experimental results, and it was found that the results were in good agreement. The results of this study may provide a reference for the practical production of platinum-clad nickel wires.
The first-step drawing process of the platinum-clad nickel composite bar was numerically simulated using DEFORM 3D finite element analysis software. The Taguchi method was used to study the effect of the first-step drawing parameters (the semi-angle of die α, the friction coefficient between the platinum tube and die μ1, the friction coefficient between the platinum tube and nickel rod μ2 and the outer diameter of the original platinum tube D) on the effective stress of platinum-clad nickel bar. Then, the optimal combination of parameters (D = 7.55 mm, μ1 = 0.2, μ2 = 0.3, α = 3°) was obtained. Furthermore, the results of the deformation behavior, cladding behavior, stress effectiveness and the distribution of the damage of the composite bar using optimization schemes were compared and analyzed with Numerical Simulations 8, which showed the worst result. Meanwhile, the experimental results were in general agreement with the simulation results of optimal combination of parameters, indicating that our simulation results are plausible. This has certain guidance significance to improve the quality of platinum-clad nickel composite wires in actual production.
To simultaneously suppress shrinkage-related defects and refine the solidification microstructure of Mn70Ni25Cr5 alloy ingots, ProCAST simulation was combined with Box–Behnken response surface methodology to optimize pouring temperature, filling time, and mold temperature. Porosity in the ingot body and secondary dendrite arm spacing (SDAS) were selected as the response variables, and quadratic regression models were established for both responses. The optimized casting parameters were determined using analysis of variance, response surface analysis, and the desirability function approach. The porosity and SDAS models were both statistically significant, with non-significant lack-of-fit terms and R2 values of 0.9906 and 0.9901, respectively. The optimal parameters were a pouring temperature of 1220.74 °C, a filling time of 6.34 s, and a mold temperature of 294.47 °C, corresponding to a predicted porosity of 0.426% and a predicted SDAS of 47.51 μm. A supplementary simulation and a validation casting experiment were then performed using practical process settings derived from the optimized solution. The supplementary simulation indicated that shrinkage-related defects were concentrated mainly in the riser, while metallographic examination revealed no large continuous shrinkage-porosity region in the examined ingot-body sections. The overall measured SDAS across the center, half-radius, and edge positions was 48.54 μm, differing from the response-surface prediction by approximately 2.2%. These results support the applicability of the combined ProCAST–RSM approach for simulation-assisted optimization of Mn70Ni25Cr5 alloy casting parameters within the investigated process range.
Platinum-clad nickel composite wires with platinum layer thicknesses of 5 μm and 8 μm were prepared by a cladding drawing process. Oxidation experiments were performed using a muffle furnace at temperatures of 500 °C, 600 °C, 700 °C, and 800 °C for 1 h, 2 h, and 3 h. The oxidized samples were examined for high-temperature oxidation behavior using scanning electron microscopy (SEM) with an energy-dispersive X-ray (EDX) spectrometer attached. The results showed that the interface bond between the platinum cladding and the nickel core wire was serrated and that the thickness of the platinum cladding was not uniform. At low temperatures (500 °C and 600 °C), the diffusion rate of the nickel was low. The composite wire could be used for a short time below 600 °C. When the temperature reached 700 °C and above, the nickel diffused to the surface of the composite wire and was selectively oxidized to form a nickel oxide layer. The research results provide a theoretical reference for the selection of a service temperature for platinum-clad nickel composite wires used as the lead material for thin-film platinum resistance temperature sensors.