Reducing diesel engine emissions under cold start conditions has become much more valuable as environmental issues become more important. Regarding diesel engine emissions under cold start conditions, this review summarizes the emission mechanisms and specifically focuses on the research progress of four reduction strategies: biodiesel utilization, intake heating, injection optimization, and aftertreatment technologies. In general, adding biodiesel and Di-Ethyl-Ether (DEE) could provide the benefit of reducing emissions and maintaining engine performance. Intake heating and appropriate injection strategies could also effectively reduce emissions under cold start conditions. Unlike normal operating conditions, lean nitrogen oxide traps (LNT) or electrically heated catalysts (EHC) should be utilized in the aftertreatment of diesel engines to minimize emissions under cold start conditions. By offering the valuable information above, this review could be a helpful reference in reduction strategies for diesel engines under cold start conditions in both academia and industry.
1
4 January 2022 in Polish Journal of Environmental Studies
Side-stream smoke from cigarettes contains formaldehyde, inhalable particulate matter and other pollutants, which seriously affects human health. The formaldehyde and inhalable particles in sidestream smoke emitted from four common brands of cigarettes in an environmental chamber were monitored by using a hand-held formaldehyde detector and a particulate detector. The concentration of the pollutants was also studied under conditions of closeness, natural ventilation and mechanical ventilation. The results show that the burning rates of four brands of cigarettes range from 2.65 to 3.0 g/h in the enclosed environment chamber and the peak concentrations of formaldehyde emissions range from 1.02 to 1.72 mg/m3. The release process of particulate matter can be divided into release diffusion stage and sedimentation stage. The peak concentrations of PM2.5 and PM10 is 0.282 and 3.382 mg/m3, respectively. The sedimentation rates of PM2.5 and PM10 are 0.0180 and 0.0289 mg/m3.h-1, respectively. It is found that the removal rate of formaldehyde and particulate matter is positively correlated with the ventilation rate. The fitting correlation coefficients of formaldehyde concentration during the rise and fall phases under closed conditions are greater than 0.968 and 0.979, respectively, and the coefficients of PM2.5 and PM10 are greater than 0.904 and 0.929, respectively.
Nowadays it has become particularly valuable to control the Particulate Matter (PM) emissions from the road transport sector, especially in vehicle powertrains with an Internal Combustion Engine (ICE). However, almost no publication has focused on a comparison of the microscopic characteristics of gasoline and ethanol spray under injection pressure conditions of more than 30 MPa, except in the impingement process. By using a Phase Doppler Particles Analyser (PDPA) system, the microscopic characteristics of gasoline and ethanol spray from a Gasoline Direct Injection (GDI) injector under injection pressure () up to 50 MPa was fully explored in this research. The experimental results demonstrate that under the same , the second peak of the probability () curves of droplet normal velocity for gasoline is slightly higher than that of ethanol. Moreover, gasoline spray exceeds ethanol by about 5.4% regarding the average droplet tangential velocity at 50 mm of jet downstream. Compared to ethanol, the curve’s peak of droplet diameter at (0, 50) for gasoline is 1.3 percentage points higher on average, and the overall Sauter mean diameter of gasoline spray is slightly smaller. By increasing from 10 MPa to 50 MPa, of the regions of “100 ≤ Weber number () < 1000” and “ ≥ 1000” increases by about 23%, and the of large droplets over 20 μm shows a significant reduction. This research would provide novel insights into the deeper understanding of the comparison between gasoline and ethanol spray in microscopic characteristics under ultra-high . Additionally, this research would help provide a theoretical framework and practical strategies to reduce PM emissions from passenger vehicles, which would significantly contribute to the protection and sustainability of the environment.
The climate change issue has become a growing concern due to the increasing greenhouse gas emissions. To achieve carbon neutrality for mitigating the climate problem, the oxy-fuel combustion (OFC) technique on internal combustion engines (ICEs) has attracted much attention. Furthermore, the water injection (WI) strategy was proven effective in improving the combustion process and thermal efficiency in engines under OFC mode. However, WI strategy effects on gasoline direct injection (GDI) engines fuelled with gasoline–alcohol blends have not been reported. This study quantitatively analysed WI mass and timing effects on oxy-fuel combustion performance from a GDI engine fuelled with E10 (10% ethanol and 90% gasoline in mass) by simulation. The results show that equivalent brake-specific fuel consumption (BSFCE) shows a monotonically decreasing trend with the increase in the water–fuel mass ratio () from 0 to 0.2. However, further increasing would cause a deterioration in BSFCE due to the enhanced cooling effects of water vaporisation. Moreover, an appropriate water injection timing () could be explored for improving OFC performance, especially for large conditions. The difference in BSFCE between = −100°CA and = −60°CA can be up to around 6.3 g/kWh by increasing to 0.6.
In order to explore the combustion performance of a non-road air-cooled two-cylinder turbocharged diesel engine, an experiment on the effects of engine compression ratio, combustion chamber shape and injection timing were systematically conducted in this study. Moreover, the effects of intake air conditions on combustion performance were numerically investigated using the one-dimensional simulation platform. The findings of this study could help provide new insights for promoting the sustainable development of diesel engines used in generator sets. The results show that the increase of intake air temperature can delay the combustion center of gravity, and improve the combustion performance and the sustainability of diesel engines. The decrease of intake air pressure will lead to a reduction in oxygen amount during the combustion process, thus causing a deterioration of cylinder pressure and combustion performance. By modifying the combustion chamber, the ignition delay and combustion duration are each extended by 1.6 degrees and 4.2 degrees under 100% engine load. The ignition delay and combustion duration are not obviously affected by modifying the combustion chamber shape under 25% and 50% loads. By increasing the compression ratio from 19.5 to 20.5, the ignition delay and combustion duration are shortened, which could enhance the cylinder pressure and heat release rate. However, reducing the compression ratio from 19.5 to 18.5 could significantly decrease the heat release rate. Under middle and low loads, combustion duration is less affected by injection timing. Under 100% load, the peak cylinder pressure increases to 11.4 MPa, and the ignition delay is shortened by advancing injection timing from -17°CA to -20°CA.
In order to explore the combustion performance of a non-road air-cooled two-cylinder turbocharged diesel engine, an experiment on the effects of engine compression ratio, combustion chamber shape and injection timing were systematically conducted in this study. Moreover, the effects of intake air conditions on combustion performance were numerically investigated using the one-dimensional simulation platform. The findings of this study could help provide new insights for promoting the sustainable development of diesel engines used in generator sets. The results show that the increase in intake air temperature can delay the combustion center of gravity and improve the combustion performance and the sustainability of diesel engines. The decrease in intake air pressure leads to a reduction in oxygen amount during the combustion process, thus causing the deterioration of cylinder pressure and combustion performance. By modifying the combustion chamber, the ignition delay and combustion duration are each extended by 1.6 degrees and 4.2 degrees under 100% engine load. The ignition delay and combustion duration are not obviously affected by modifying the combustion chamber shape under 25% and 50% loads. By increasing the compression ratio from 19.5 to 20.5, the ignition delay and combustion duration are shortened, which could enhance the cylinder pressure and heat release rate. However, reducing the compression ratio from 19.5 to 18.5 could significantly decrease the heat release rate. Under middle and low loads, combustion duration is less affected by injection timing. Under 100% load, the peak cylinder pressure increases to 11.4 MPa, and the ignition delay is shortened by advancing injection timing from −17 °CA to −20 °CA.