High-temperature superconducting (HTS) pinning maglev has the potential for high-speed application because of its advantages of passive self-stabilization, energy conservation, environmental protection, and no inherent magnetic resistance along the forward direction. The HTS pinning maglev can realize non-contact levitation and guidance. Permanent magnet linear synchronous motor (PMLSM) is suitable for HTS pinning maglev to realize non-contact drive. However, in addition to the longitudinal driving force for the HTS pinning maglev train, the PMLSM also produces the normal force which will cause additional excitation on the maglev train and affect its levitation height and vertical dynamic response. In this paper, a coreless-typed PMLSM is designed for HTS pinning maglev driving system, and the driving force and normal force characteristics of the motor under different air gaps are calculated. Then, a vertical dynamic model of the HTS pinning maglev vehicle is established. The vertical dynamic response of the HTS pinning maglev vehicle excited by the normal force of PMLSM and permanent magnet guideway (PMG) irregularity is simulated and analyzed. This work can provide a reference for the study of the electromechanical coupling effect between the HTS pinning maglev levitation system and linear motor driving system.
21 November 2022 in IEEE Transactions on Magnetics
The permanent magnet electrodynamic wheel system is a competitive alternative for the implementation of maglev car due to its levitation-propulsion integration ability. However, the temperature rise of conductive plate may deteriorate operation performance even result in suspension failure, which underlines the importance of thermal analysis. In this article, the thermal-force coupling analysis is conducted by experiment combined with the co-simulation method. Firstly, the heat resource generated by power loss in the conductive plate is obtained and verified by analytical model, simulation and experiment, and the lumped thermal model is presented. Additionally, a knowledge of the transient temperature distribution and the variation of electromagnetic forces under different speeds are studied. Eventually, a proof-of-concept prototype of maglev car with its auxiliaries was manufactured and used for further thermal analysis. Temperature management is considered by increasing the volume of conductive plate and cooling the conductive plate via water medium, and a good heat dissipation effect is realized. The results reveal that the levitation forces have a pronounced attenuation because of the temperature, with percentage of 38.8% and 37.4% respectively with respect to the initial room temperature. In low-speed region, the propulsion forces yield a subtle increase while it decreases slightly in high-speed region. Lowering the temperature can be accomplished by increasing conductive plate volume or adopting water cooling. This paper lays a temperature-related co-simulation method and experiment basis, and pave the way for considering the thermal effect in the practical application.
23 May 2018 in IEEE Transactions on Plasma Science
In this paper, a new structure of coilgun with stepped coil winding was designed. The performance of this structure was investigated and compared to the conventional coilgun with uniform diameter stator coil (UDSC) winding. It can be seen from the results that the trigger position of this new structure moves forward with respect to the conventional coilgun. In order to compare the results, the inductance of the two coils is set to the same. If the initial voltage of the capacitor is lower, as the armature at the optimum trigger position, the muzzle velocity of armature in the conventional UDSC coilgun is relatively larger. Conversely, if the initial voltage of the capacitor is higher, the muzzle velocity of armature in the new structure coilgun is relatively larger. According to the simulation results with the increase of voltage, the difference is more and more obvious. Through the single-stage preliminary experiment in our laboratory, the results were in good agreement with the simulation results. And the trigger position is more forward, so the interaction time between the armature and the coil will be longer. Besides, the coil with stepped structure will increase the efficiency of the coilgun when the voltage level is higher.
15 November 2023 in IEEE Transactions on Instrumentation and Measurement
High-temperature superconducting (HTS) magnetic levitation (Maglev) holds great promise as a high-speed transportation system of the future. To fully exploit its potential, enhancing localization precision is of utmost importance, necessitating the multifusion of relative and absolute positioning. Currently, there exists a dearth of research on fusion localization tailored specifically for HTS Maglev trains. This article presents a method for multisensor data fusion to detect the position of HTS Maglev trains. The position detection system comprises a tunnel magneto resistance (TMR) sensor, an inertial measurement unit (IMU) module, and an absolute positioning system utilizing radio frequency identification (RFID). By utilizing the three-channel data, a truth-correction extended Kalman filter (EKF) algorithm is developed, which can dramatically reduce the positioning error. The error model and simulation analysis of the subsystem and fusion algorithm are established to accommodate various working conditions. Furthermore, a test platform is constructed to verify the performance of the position detection system. The simulation and experimental results demonstrate that the truth-correction-based multisensor fusion method improves measurement accuracy and meets the requirements of engineering applications.
4 November 2019 in IEEE Transactions on Applied Superconductivity
This paper puts forward a method based on high temperature superconducting (HTS) current limiting technology, to improve the over-current stability for a battery unit in a superconducting magnetic energy storage (SMES)-battery hybrid energy storage systems (HESS). In contrast to supercapacitors, flywheels and other energy storage systems, SMES-battery HESS possess the technical properties of power capacity, energy and response speed, among other. Thus, SMES-battery HESS may be utilized to handle power swing, energy transfer, voltage fluctuation and related transient stability issues. But an over-current in a battery unit is harm to its cycle life of the battery. Hence, the internal protection system of the battery unit is used to remove a fault by cutting off its outputs. In this paper, a ${\rm{YBa_{2}Cu_{3}O_{7-X}\ (YBCO)}}$ thin film is employed as the protection device to limit the over-current in a battery unit. In normal operation, the thin film is in the superconducting state, and its influence on the system can be ignored. An over-current will be limited evidently lower than the action threshold of the internal protection system by the quench resistance of the thin film. Therefore, the whole outputs of a battery unit will not be interrupted and restarted. Through the verification experiment carried out in our laboratory, the proposed protection method operated as expected, and the stability, as well as the reliability of the battery unit, could be improved.
6 April 2018 in IEEE Antennas and Wireless Propagation Letters
A circularly polarized (CP) patch antenna with a new chiral metamaterial structure was proposed. The proposed CP antenna is composed of a conventional linearly polarized patch antenna and a chiral metamaterial (CMM) board. For the CMM unit cell, the geometric parameters of the two pieces of copper films that are patterned on opposite sides of an FR-4 board are quite different. The function that a linear-polarization wave is converted into a circular polarization wave can be realized by the designed structure through simulation verification. When the CMM board is placed in the front of a conventional linear-polarized patch antenna, the antenna polarization mode can be changed to the circular polarized mode. The antenna performances have been investigated numerically and experimentally. Meanwhile, the new CMM structure could be applied to the field of circular-polarized antenna.