Bolt support mechanisms represent a key technique to support the surrounding rock in coal mines. In deep rock engineering applications, the bolt‐supported structure of the surrounding rock of a deep roadway under high bearing stress may fail under dynamic loads such as those of blasting vibrations and earthquake motion. In this study, dynamic uniaxial compression tests were conducted on steel bar reinforced rock to investigate the rockbolt performance under dynamic loading. The deformation of the specimen surface and rockbolt was recorded during the test. The strengths and failure modes of the bolted rock samples were investigated. The results show that the bolt and rock deform asynchronously when the bolted specimen is subjected to a dynamic load, and the time of the asynchronous deformation of the specimens with different bolt angles is considerably different. When the stress wave acts along the direction of the bolt, it is more likely to cause the failure of the bolted specimen. Anchorage agents should be employed to realize the synchronous deformation of the bolt and rock mass. The slip and dislocation of the anchorage agent/rock surface and anchorage agent/bolt interface are the key factors influencing the failure of bolted specimens. The influence of a dynamic stress wave on the surrounding rock support structure of a deep roadway can be effectively reduced by improving the antisliding characteristics of the anchoring agent and increasing the bolt density. The research results can provide theoretical guidance and serve as a reference to realize the reinforcement engineering of underground permanent chambers and roadways.
Because kaolinite includes a large range of defect elements, the effects of Mg, Fe(II), and Al doping on the CH4 adsorption and diffusion on the surface of Na-kaolinite (001) were investigated by molecular simulations. The simulation results illustrate that ion doping can significantly reduce the amount of CH4 adsorbed by kaolinite, but the type of doped ions has little effect on the amount of adsorption. The specific surface area of kaolinite and the interaction energy between CH4 and the kaolinite’s surface are two key factors that can determine CH4 adsorption capacity. The first peak value of the radial distribution functions (RDFs) between CH4 and the pure kaolinite is larger than that between Mg-, Fe(II)-, and Al-doped kaolinite, which indicates that ion doping can reduce the strength of the interactions between CH4 and the kaolinite’s surface. Besides hydrogen and oxygen atoms, interlayer sodium ions are also strong adsorption sites for CH4 and lead to a weakened interaction between CH4 and the kaolinite’s surface, as well as a decrease in CH4 adsorption. Contrary to the adsorption results, ion doping facilitates the diffusion of CH4, which is beneficial for actual shale gas extraction.
Using the self-developed “TCHFSM-I” large-size true triaxial fracturing seepage simulation device and fluid injection flow dynamic monitoring device, we studied the crack initiation and expansion law of multi-fractures under different perforation spacing conditions and revealed the mechanism of multi-fractures expanding from non-equilibrium to equilibrium on the basis of the evolution law of the injection pressure and characteristics of the distribution of the injection flow. The results show that when the perforation spacing is small (<60 mm), the central injection fracturing cracks are affected by the extension of the upper and lower injection cracks, and their extension lengths are shorter; on the contrary, the extension lengths of the upper, central and lower injection cracks are basically the same, and the three hydraulically fractured cracks shift from non-equilibrium to equilibrium extension. When the perforation spacing is small, the fracture initiation pressure of the middle perforation is much larger than that of the upper and lower perforations. However, as the perforation spacing increases, the fracture initiation pressure of the middle perforation gradually decreases. Its fracture initiation pressure is basically the same as that of the upper and lower perforations. The expansion of the three hydraulically fractured cracks is independent of each other. In addition, the evolution law of the injection flow rate can better reflect the multi-fracture fracture initiation and expansion pattern, and the evolution pattern of the injection flow rate can better reflect the synchronous fracture initiation and expansion mechanism of multi-fracture fracture. The results of the study can provide technical guidance for efficient coalbed methane extraction.
The thesis, from the character of hard roof on longwall working face, moving character and control request, by establishing mechanical model and theoretic deduced method, achieves supporting strength of the breaker props and pressure interval control under the control of hard roof on longwall working face, and therefore realizes managing the hard roof safely and effectively.
Mining operations conducted beneath water-bearing strata pose significant risks associated with the development of water-conducting fracture zones in the overburden. The height criterion for this parameter is critical to ensuring the stability of underground mine workings and preventing the risk of water inrush incidents. The research is based on physical and numerical simulations and aims to forecast the development of the water-conducting fracture zone. The methodology is based on in situ hydrogeology data, geotechnical boreholes, physical 2D modeling of rock strata, discrete element modeling using UDEC, and finite–discrete element modeling using Prorock software. A physical model of layered rock mass is constructed to simulate unfilled excavation areas induced deformation under real polymetallic ore field conditions. Based on the results, relationships between vertical subsidence, layer curvature, inclination, and the height of the water-conducting fracture zone were obtained. Particular attention is given to the effects of tectonic discontinuities, chamber geometry, and backfilling on fracture development. A stepwise excavation sequence is simulated to reproduce field conditions and assess the evolution of stress and deformation fields in the overburden. The study reveals that the propagation of the fracture zone around a mine excavation adheres to a polynomial law, characterized by an increase in height concurrent with the expansion of the excavation. This approach enables the design of safe extraction strategies beneath aquifers or surface water bodies. The proposed framework is expected to enhance prediction accuracy and reduce uncertainties.
Remaining coal pillars in remining areas exhibit clear creep characteristics, and dynamic pressure accelerates their instability and failure. The creep and hardening characteristics of coal under dynamic pressure are of great engineering significance for the stability of remaining coal pillars in remining areas and their control. To investigate the creep and hardening characteristics of anthracite under static–dynamic coupled loading, graded loading creep tests with different loading rates were conducted. In this research, the creep strain, instantaneous elastic modulus, and creep rate of anthracite were studied under different graded loading rates. The results showed that the hardening effect of the samples manifested as an increasing instantaneous elastic modulus at the loading stage and a decreasing strain rate at the creep stage. When the graded loading rate increases from 0.01 to 0.1 mm/s, the instantaneous elastic modulus increases by 0.16–2.32 times. The sudden increase in the instantaneous elastic modulus at the failure stress level explains the instantaneous failure of the samples well. The actual yield levels corresponding to the peak instantaneous elastic modulus of the samples linearly decreased with increasing graded loading rate. The functional relationship between the graded loading rate and the elastic modulus hardening coefficient, the actual yield stress, and the strain rate decay coefficient were established, which could quantitatively describe the influence of different graded loading rates on the creep and hardening characteristics of anthracite and predict its creep damage.