Acting like thermal resistances, ferroelectric domain walls can be manipulated to realize dynamic modulation of thermal conductivity (k), which is essential for developing novel phononic circuits. Despite the interest, little attention has been paid to achieving room‐temperature thermal modulation in bulk materials due to challenges in obtaining a high thermal conductivity switching ratio (khigh/klow), particularly in commercially viable materials. Here, room‐temperature thermal modulation in 2.5 mm‐thick Pb(Mg1/3Nb2/3)O3–xPbTiO3 (PMN–xPT) single crystals is demonstrated. With the use of advanced poling conditions, assisted by the systematic study on composition and orientation dependence of PMN–xPT, a range of thermal conductivity switching ratios with a maximum of ≈1.27 is observed. Simultaneous measurements of piezoelectric coefficient (d33) to characterize the poling state, domain wall density using polarized light microscopy (PLM), and birefringence change using quantitative PLM reveal that compared to the unpoled state, the domain wall density at intermediate poling states (0< d33<d33,max) is lower due to the enlargement in domain size. At optimized poling conditions (d33,max), the domain sizes show increased inhomogeneity that leads to enhancement in the domain wall density. This work highlights the potential of commercially available PMN–xPT single crystals among other relaxor‐ferroelectrics for achieving temperature control in solid‐state devices.
The vocal folds (VFs) are constantly exposed to mechanical stimulation leading to changes in biomechanical properties, structure, and composition. The development of long-term strategies for VF treatment depends on the characterization of related cells, biomaterials, or engineered tissues in a controlled mechanical environment. Our aim was to design, develop, and characterize a scalable and high-throughput platform that mimics the mechanical microenvironment of the VFs in vitro. The platform consists of a 24-well plate fitted with a flexible membrane atop a waveguide equipped with piezoelectric speakers which allows for cells to be exposed to various phonatory stimuli. The displacements of the flexible membrane were characterized via Laser Doppler Vibrometry (LDV). Human VF fibroblasts and mesenchymal stem cells were seeded, exposed to various vibratory regimes, and the expression of pro-fibrotic and pro-inflammatory genes was analyzed. Compared to current bioreactor designs, the platform developed in this study can incorporate commercial assay formats ranging from 6- to 96-well plates which represents a significant improvement in scalability. This platform is modular and allows for tunable frequency regimes.
We develop a new processing algorithm for the analysis of high-speed quantitative polarized light microscopy measurements. The measurements are obtained using a high-speed rotating polarizing component and a camera, collecting images at several polarizer angles per rotation. The technique uses data from less than the full quarter-waveplate rotation and then performs an optimal fit of the measured data to the expected response curves. Thus, it allows to increase the effective frame rate of the alignment angle and retardation maps due to the reduction in required images. Due to the complexity of the intensity response curves, a particle swarm optimization method is applied. The algorithm addresses the motion error in high-speed polarization imaging while still using multiple polarization angles for the reconstruction. We apply the algorithm to two example cases: quasi-static loading of a tensile coupon and quality inspection of a polymer fiber during rapid motion. The results demonstrate that increasing the reconstructions per second (i.e., decreasing the number of polarization angles per reconstruction) does not significantly decrease the quality of the reconstructions until ∼2.5 times the increase in reconstructions per second is achieved. Therefore, the developed algorithm is an effective method to increase the effective polarization imaging rate without complex hardware modifications.
Ferroelectric domain walls separate regions of uniform polarization in ferroelectric materials, and their controlled manipulation, such as through electric poling, is essential for enhancing the electromechanical performance of advanced ferroelectric devices. While most existing imaging techniques only examine static domain structures at the pre- or post-poling state, real-time, in situ, and non-destructive visualization of internal domain wall dynamics during electric poling using a simple implementation remains a significant challenge. In this work, we present a simple and accessible optical technique, instant polarized light microscopy (IPOLπ), for through-volume, single-shot, and in situ observation of domain wall evolution during electric poling. Demonstrated on [110]-oriented Pb(In1/2Nb1/2)O3–Pb(Mg1/3Nb2/3)O3–PbTiO3 single crystals, IPOLπ enables direct observation of polarization dynamics during alternating current poling and electrical depoling. The method reveals the formation of layered domain structures initiating at sample edges and progressing inward, as well as the correlation between optical birefringence changes and electrical current response. This low-cost, robust technique provides a powerful tool for studying real-time domain wall behavior, offering new insights into structure–property relationships in functional ferroelectric crystals.
An in situ, high-speed polarization imaging method is developed and implemented for the detection of abnormalities in polymer fibers during production. The images are initially adjusted through a motion tracking algorithm. Depending on the production and image acquisition rates, the image analysis can then be processed through two methods, with the latter allowing for an increase in imaging frequency through data modeling. The imaging method is applied in both pre- and post-quenching conditions. The post-quenching results demonstrate the ability to detect defects once the polymer has reached a sufficient crystallization state.
We amplify the signal coupled from ultrasonic Lamb waves into an optical fiber, for structural damage detection applications, using two devices: an ultrasonic horn and a phononic crystal GRIN lens.