The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. In this paper, we propose to investigate a force sensor design combining Surface Acoustic Wave (SAW) strain sensor with binocular load cell structure. For this purpose, we use a binocular test body instrumented with both resistive strain gauge as a reference and SAW strain sensor. The system enables the generation of extremely localized and accurate positive and negative strains. Static and dynamic measurements are performed using calibrated weights and a shock hammer respectively. For SAW sensor, a one-port resonator with frequency operation in the range of 410MHz was fabricated and mounted on the test body. For electronic conditioning, we use a low-cost RF electronic conditioning based on radar architecture using the integrated circuit AD8302. The system enables the measurement of S 11 reflection coefficient (module and phase) with sensitivity and noise spectral density of (29 mV/dB, 250 nV/√Hz) and (10 mV/°, 83 nV/√Hz) respectively. The SAW sensor mounted on body proof was successfully tested in static and dynamic mode using this electronic architecture. The results show good linearity, sensitivity values of 0.023 mV/ppm and 0.09 mV/ppm were obtained for amplitude and phase measurements respectively. The dynamic response was performed using a shock hammer and a comparison with conventional strain gauge shows a good agreement.
In this study, we conduct a comprehensive investigation to enhance the performance of shear surface acoustic wave (SAW) magnetic sensors. We explore the interaction between SAW and a nickel film deposited on ST-cut quartz in a delay line configuration. The nickel film, measuring 2 mm in width and 100 nm in thickness, undergoes vacuum annealing at 500 C to induce magnetic anisotropy through the anisotropic thermal properties of ST-cut quartz. Our research combines theoretical and experimental approaches to evaluate the S21 phase shift in response to an applied magnetic field. The results demonstrate a remarkable agreement between theoretical predictions and experimental data. To interpret the sensor's response behavior, we introduce a custom piezomagnetic model. Notably, we observe a phase shift difference between minimum and maximum of approximately 30 for a propagation path of 2 mm . We further investigate the impact of incorporating an SiO2 layer on top of the magnetic thin film. This addition doubles the phase shift difference, as shear SAWs become more confined near the surface or entirely waveguided within the SiO2 layer. Additionally, we explore an innovative approach for modifying the sensor's response behavior by manipulating the magnetic thin film's anisotropy. These findings contribute to the advancement of SAW magnetic sensor technology, offering enhanced sensitivity and performance through the integration of magnetic thin films and SiO2 layers.
New designs based on S0 Lamb modes in AlN thin layer resonating structures coupled with the implementation of structural elements in SiO2, are theoretically analyzed by the Finite Element Method (FEM). This study compares the typical characteristics of different interdigital transducer (IDTs) configurations, involving either a continuous SiO2 cap layer, or structured SiO2 elements, showing their performance in the usual terms of electromechanical coupling coefficient (K2), phase velocity, and temperature coefficient of frequency (TCF), by varying structural parameters and boundary conditions. This paper shows how to reach temperature-compensated, high-performance resonator structures based on ribbon-structured SiO2 capping. The addition of a thin diamond layer can also improve the velocity and electromechanical coupling coefficient, while keeping zero TCF and increasing the solidity of the membranes. Beyond the increase in performance allowed by such resonator configurations, their inherent structure shows additional benefits in terms of passivation, which makes them particularly relevant for sensing applications in stern environments.
Surface Acoustic Wave (SAW) sensors represent a prominent technological avenue for quantifying mechanical stress-induced deformations. Nonetheless, the integration of these Micro-Electro-Mechanical Systems (MEMS) sensors remains an complex challenge. Consequently, a common approach within a multitude of research involves the utilization of a adhesive formulation. However, this mode of integration continues to exhibit deficiencies in terms of measurement repeatability, particularly when confronted with harsh environments characterized by pronounced mechanical and thermal stresses. In this context, the utilization of backside reflow soldering for SAW sensor integration stands as a notably dependable alternative to epoxy bonding. In this article, we present the results of our feasibility study concerning the reflow soldering of a SAW sensor onto a binocular copper load cell to measure static strains and a ferromagnetic steel sheet to measure dynamic strains resulting from magnetostriction. To use reflow soldering, a nickel/copper electrodeposition on the ferromagnetic steel sheet was carried out, demonstrating the potential to apply this technique to various materials. The results have indicated that reflow soldering enhances the transmission of static and dynamic mechanical stresses to the SAW sensor, exhibiting a coefficient threefold greater than that achieved through simple adhesive bonding. Furthermore, this integration technique demonstrated a long-term stability of the measurement.
Magnetic field sensors combining surface acoustic waves (SAW) and magnetostrictive thin films have shown promising sensitivity in laboratory studies, but their translation into real-world applications has remained limited. In this work, we report the first practical deployment of a shear-horizontal SAW magnetic sensor for the characterization of ferromagnetic electrical steels, which are key materials for the fabrication of high-efficiency electrical machines. The proposed sensor design is built on a Quartz substrate and features a nanostructured TbCo₂/FeCo film (140 nm) overlaid with a 700 nm SiO₂ layer that enhances shear-wave confinement and protects the surface. The sensor chip is then integrated directly onto the surface of a ferromagnetic lamella. Using a compact radar-based RF circuit (AD8302 IC), we achieve phase-sensitive detection with a sensitivity of ~91 V/T and a noise spectral density of 83 nV/√Hz. Both static and dynamic magnetic losses were measured at the lamella surface, showing excellent agreement with Hall sensor benchmarks. This study establishes the first proof of concept for the application of SAW magnetostrictive sensors, demonstrating their potential as a powerful tool for the in-situ characterization and monitoring of ferromagnetic materials in electrical engineering.