The array interferometric synthetic aperture radar (Array InSAR) system resolves shadow issues by employing two scans in opposite directions, facilitating the acquisition of a comprehensive three-dimensional representation of the observed scene. The point clouds obtained from the two scans need to be transformed into the same coordinate system using registration techniques to create a more comprehensive visual representation. However, the two-point clouds lack corresponding points and exhibit distinct geometric distortions, thereby preventing direct registration. This paper analyzes the error characteristics of array InSAR point clouds and proposes a robust registration method for array InSAR point clouds in urban scenes. It represents the 3D information of the point clouds using images, with pixel positions corresponding to the azimuth and ground range directions. Pixel intensity denotes the average height of points within the pixel. The KAZE algorithm and enhanced matching approach are used to obtain the homonymous points of two images, subsequently determining the transformation relationship between them. Experimental results with actual data demonstrate that, for architectural elements within urban scenes, the relative angular differences of registered facades are below 0.5°. As for ground elements, the Root Mean Square Error (RMSE) after registration is less than 1.5 m, thus validating the superiority of the proposed method.

Circular synthetic aperture radar (CSAR) possesses the capability of multi-angle observation, breaking through the geometric observation constraints of traditional strip SAR and holding the potential for three-dimensional imaging. Its sub-wavelength level of planar resolution, resulting from a long synthetic aperture, makes CSAR highly valuable in the field of high-precision mapping. However, the motion geometry of CSAR is more intricate compared to traditional strip SAR, demanding high precision from navigation systems. The accumulation of errors over the long synthetic aperture time cannot be overlooked. CSAR exhibits significant coupling between the range and azimuth directions, making traditional motion compensation methods based on linear SAR unsuitable for direct application in CSAR. The dynamic nature of flight, with its continuous changes in attitude, introduces a significant deformation error between the non-rigidly connected Inertial Measurement Unit (IMU) and the Global Positioning System (GPS). This deformation error makes it difficult to accurately obtain radar position information, resulting in imaging defocus. The research in this article uncovers a correlation between the deformation error and radial acceleration. Leveraging this insight, we propose utilizing radial acceleration to estimate residual motion errors. This paper delves into the analysis of Position and Orientation System (POS) errors, presenting a novel high-resolution CSAR motion compensation method based on airborne platform acceleration information. Once the system deformation parameters are calibrated using point targets, the deformation error can be directly calculated and compensated based on the acceleration information, ultimately resulting in the generation of a high-resolution image. In this paper, the effectiveness of the method is verified with airborne flight test data. This method can compensate for the deformation error and effectively improve the peak sidelobe ratio and integral sidelobe ratio of the target, thus improving image quality. The introduction of acceleration information provides new means and methods for high-resolution CSAR imaging.

Real-world environment-derived point clouds invariably exhibit noise across varying modalities and intensities. Hence, point cloud denoising (PCD) is essential as a preprocessing step to improve downstream task performance. Deep learning (DL)-based PCD models, known for their strong representation capabilities and flexible architectures, have surpassed traditional methods in denoising performance. To our best knowledge, despite recent advances in performance, no comprehensive survey systematically summarizes the developments of DL-based PCD. To fill the gap, this paper seeks to identify key challenges in DL-based PCD, summarizes the main contributions of existing methods, and proposes a taxonomy tailored to denoising tasks. To achieve this goal, we formulate PCD as a two-step process: outlier removal and surface noise restoration, encompassing most scenarios and requirements of PCD. Additionally, we compare methods in terms of similarities, differences, and respective advantages. Finally, we discuss research limitations and future directions, offering insights for further advancements in PCD.

Impulse ultrawideband (UWB) synthetic aperture radar (SAR) combines high-azimuth-range resolution with robust penetration capabilities, making it ideal for applications such as through-wall detection and subsurface imaging. In such systems, the performance of UWB antennas is critical for transmitting high-power, large-bandwidth impulse signals. However, two primary factors degrade radar imaging quality: (1) inherent limitations in antenna radiation efficiency, which lead to low-frequency signal loss and subsequent time-domain ringing artifacts; (2) impedance mismatch at the antenna terminals, causing standing wave reflections that exacerbate the ringing phenomenon. This study systematically analyzes the mechanisms of ringing generation, including its physical origins and mathematical modeling in SAR systems. Building on this analysis, we propose a Bayesian ringing suppression algorithm based on sparse optimization. The method effectively enhances imaging quality while balancing the trade-off between ringing suppression and image fidelity. Validation through numerical simulations and experimental measurements demonstrates significant suppression of time-domain ringing and improved target clarity. The proposed approach holds critical importance for advancing impulse UWB SAR systems, particularly in scenarios requiring high-resolution imaging.

Tomographic synthetic aperture radar (TomoSAR) possesses 3D imaging capability, making it significant for building reconstruction using TomoSAR data. The reconstruction algorithm is closely related to building point cloud detection, while traditional detection methods suffer from low automation and reliance on manual configuration. This study proposes a building point cloud reconstruction method based on deep learning semantic segmentation. Initially, deep learning method is employed for end‐to‐end building point cloud segmentation, followed by point cloud reconstruction based on the segmentation results. The proposed method is simple and efficient, elevating the level of automation in point cloud processing. Experimental validation on real TomoSAR data confirms that the proposed method achieves automated and refined reconstruction of building point clouds.

The introduction of tomographic synthetic aperture radar (TomoSAR) technology into the field of through-wall perception enables high-resolution 3D imaging of behind-wall targets, enhancing reconnaissance capabilities for applications such as urban counter-terrorism and disaster response. Unlike airborne tomographic SAR systems, vehicle-mounted through-wall tomographic SAR (TW-TomoSAR) operates at shorter ranges and involves propagation through layered media, which induces wavefront curvature errors (WCE) and medium path errors (MPE). These errors manifest as target defocusing and positional inaccuracies in reconstructed images. This paper proposes an efficient processing architecture for TW-TomoSAR. Following 2D SAR imaging, wavenumber-domain MPE compensation is performed using phase correction functions derived from equivalent transmission models. Subsequently, WCE correction is accomplished using keystone transformation in the complex image domain, allowing the height reconstruction process to be separated, simplifying the 3D imaging workflow. Finally, Bayesian super-resolution reconstruction incorporating Laplace priors is adopted to overcome antenna size limitations in elevation resolution. The practical implementation of the proposed TW-TomoSAR demonstrates high-resolution imaging of targets behind walls.