Low‐temperature lithium metal batteries (LT‐LMBs) are increasingly desired for higher energy density and longer lifespan. However, due to organic electrolyte solidification, LT‐LMBs are impeded by huge barriers resulting from the hindrance of larger solvation shells with strong ion‐dipole interactions, leading to depressive Li kinetics and severe dendrite formation. Herein, interfacial catalysis by constructing electron delocalization d ‐orbital metal oxides toward the ion‐dipole interactions is pioneered to accelerate the larger Li(solvents) x+ dissociation under the low‐temperature environment. Specifically, various kinds of d ‐orbital metal oxides (M = Ti, V, Fe, Co) with oxygen defect modulation are systematically screened and investigated for breaking the ion‐dipole interactions, and the prototyped titanium oxide with adjustable electron delocalization behave the best, as confirmed by electrochemical and theoretical experiments. Consequently, optimized Li electrodes withstand environmental robustness from 25 to −50°C, and stabilize long‐term cycling up to 1800 h and high Coulombic efficiency without any short‐circuit under −20°C. The as‐fabricated Li–S full cell enables a high‐capacity retention of 88% at 0.2 C over 200 cycles, and the high‐loading Li‐LiNi 0.8 Co 0.1 Mn 0.1 O 2 cell (≈20 mg cm −2 ) demonstrates excellent capacity retention ≈100% under 0°C, providing a new guideline for adopting a catalytic strategy for achieving advanced LT‐LMBs.
The perpendicular magnetic anisotropy (PMA) has been achieved in Ta/Pd/CoFeMnSi (CFMS)/MgO/Pd film, in which the Heusler compound CoFeMnSi is one of the most promising candidates for spin gapless semiconductor (SGS). The strong PMA, with the effective anisotropy constant Keff of 5.6 × 105 erg/cm3 (5.6 × 104 J/m3), can be observed in the Ta/Pd/CFMS (2.3 nm)/MgO (1.3 nm)/Pd films annealed at 300 °C. In addition, it was found that the magnetic properties of Ta/Pd/CFMS/MgO/Pd films are sensitive to hydrogen (H2) under a weak magnetic field (< 30 Oe), whose residual magnetization (Mr) decreased from 123.15 to 30.75 emu/cm3 in the atmosphere with H2 concentration of 5%.
An electron-delocalization strategy to strengthen electron hybridization between catalyst and sulfur species has been proposed to enhance Li+ transformation kinetics for a fast redox reaction at 0 or −10 °C, enabling a high-capacity retention of 85%.
Aiming at enhancing the shape anisotropy of a microwave absorber and elongating the travel distance of microwave along the absorber surface for better absorption, we fabricated the textured nanoflaky powders of Fe-B alloy through the two-step ball milling method followed by dealloying. The complex permittivity and permeability of as-dealloyed powders were characterized systematically. The results showed that the flaky powders of Fe-B with textured structure possess enhanced microwave absorption properties: an optimal reflection loss (RL = -45.8 dB) at 9.2 GHz with a matching thickness of 2.4 mm.
AISI 5120 steel, which underwent 30 min single-surface nanocrystallization via supersonic fine particle bombarding (SFPB), was pre-boronized at 600 °C for 2 h, and then final-boronized at 800 °C or 900 °C for 2–6 h, i.e., two-step pack-boronizing. The specimens’ microstructure and mechanical characteristics before and after two-step boronizing were examined in detail. The results showed that the hardness of the SFPB surface reached 570 HV, which was 2.73 times higher than its original hardness (209 HV). The nanocrystallized surface exhibited the increased thickness and hardness of the boride layer, in comparison to that of the un-SFPB surface. Two-step pack-boronizing further improved the thickness and hardness of the SFPB surface of AISI 5120 steel. When final-boronizing at 900 °C for 6 h, the thickness and hardness of the boronizing layer in the SFPB surface was 88 µm and 2196 HV, respectively, which was 10.5 times higher than the original hardness. Additionally, the CeO2 added in the boronizing agent was helpful in obtaining the boride layer with the ductile-serrated Fe2B phase rather than the brittle phase of FeB in the boride layer, which was expected for industrial applications.