To optimize the bamboo heat treatment process, the corresponding evolution rules under various heat treatment conditions must be determined. When the heat treatment time and temperature remained constant, the effects of different heat treatment pressures on the equilibrium moisture content, dimensional stability, mechanical properties, and chemical composition of bamboo were systematically investigated. In this experiment, bamboo without heat treatment was used as the control group. The experimental findings demonstrate the following: (1) The equilibrium moisture content of heat-treated bamboo gradually decreases with increasing treatment pressure. When the heat treatment pressure was set at 0.1, 0.15, 0.2, and 0.25 MPa, the bamboo’s equilibrium water content decreased to 12.1%, 11.7%, 9.9%, and 8.6%, respectively, while that of the control group was 13.8%. (2) The dimensional stability of bamboo was enhanced with increasing heat treatment pressure. At pressures of 0.1, 0.15, 0.2, and 0.25 MPa, the radial air-dry shrinkage rates of the heat-treated bamboo decreased to 3.4%, 3.4%, 2.6%, and 2.3%, respectively, while the tangential air-dry shrinkage rates reduced to 5.6%, 5.1%, 3.3%, and 3.0%. In comparison, the radial and tangential air-dry shrinkage rates of the control group were measured as 3.6% and 5.8%, respectively. Similarly, the radial and tangential full-dry shrinkage of bamboo exhibited a similar trend. (3) With the increase in heat treatment pressure, the bending strength and longitudinal compressive strength of bamboo exhibited an initial rise followed by a decline. When it was at heat treatment pressures of 0.1, 0.15, 0.2, and 0.25 MPa, the corresponding bending strengths of the heat-treated bamboo were measured as 41.2, 26.7, 22.4, and 20.4 MPa, respectively; while the longitudinal compressive strengths were recorded as 42.6, 38.1, 29.1, and 25.3 MPa. In comparison, the bending and longitudinal compressive strengths of the control group were measured as 39.8 and 38.5 MPa, respectively. It is evident that the optimal heat treatment pressure for bamboo is 0.1 MPa, resulting in a significant increase of 3.5% and 10.6% in bending strength and longitudinal compressive strength, respectively, compared to the control group. (4) Based on the FTIR and XRD patterns of bamboo samples, a range of physical and chemical transformations were observed during the heat treatment process, including cellulose adsorb water evaporation, hemicellulose and cellulose degradation, as well as acetyl group hydrolysis on the molecular chain of hemicellulose. These changes collectively impacted the physical and mechanical properties of bamboo.

Soil microorganisms play important roles in promoting soil ecosystem restoration, but much of the current research has been limited to changes in microbial community structure in general, and little is known regarding the soil physicochemical property and microbial community structure. In this study, four organic fertilizers were first prepared based on tea oil camellia shell (TOCS). Our findings indicate that the application of BOFvo increased both total pore volume and BET surface area of the rhizosphere soils, as well there was a remarkable enhancement in total organic matter (TOM), total nitrogen (TN), available nitrogen (AN), total phosphorus (TP), total potassium (TK), and available potassium (AK) contents of the rhizosphere soils. Meanwhile, in comparison to the CK and CF groups, the utilization of BOFvo led to a substantial increase in both average yield and fruiting rate per plant at maturity, as well resulted in a significant increase in TN and TP contents of tea oil camellia leaves. Furthermore, our findings suggest that the application of TOCS-based organic fertilizers significantly enhances the microbial diversity in the rhizosphere soils with Proteobacteria and Ascomycota being the dominant bacterial and fungal phyla, respectively, and Rhodanobacter and Fusarium being the dominant bacterial and fungal genus, respectively. Redundancy analysis (RDA) indicates that the physicochemical characteristics of TOCS-based organic fertilizers had a significant impact on the composition and distribution of microbial communities in the rhizosphere soils. This study will facilitate the promotion and application of TOCS-based organic fertilizers, thereby establishing a foundation for the reuse of tea oil camellia waste resources.

Microcrystalline cellulose (MCC) possesses important attributes, including high crystallinity, a large surface area, excellent mechanical strength, chemical stability, and biodegradability. This study aims to research MCC extraction from bamboo (Phyllostachys edulis (Carrière) J. Houz.) fiber by assessing the impact of key processing variables such as acid concentration, temperature, and hydrolysis duration. Experimental results indicate that hydrolysis time and hydrochloric acid (HCl) concentration significantly influence yield. After evaluating the effects of various hydrolysis conditions, the optimal parameters were determined to be a 2.0 M HCl concentration, 90 °C, and 10 min of reaction time. The MCC produced under optimal conditions displayed improved crystallinity (77.2%) while retaining functional groups similar to those found in raw bamboo. Morphological analysis revealed an irregular rod-like shape with rough surfaces. This optimized hydrolysis process offers a viable approach for MCC production from raw bamboo and holds potential as a precursor for developing environmentally friendly biodegradable fiber materials.

Bamboo is readily discolored by mold fungi, which greatly limits its applications. An effective antifungal agent, copper(II) chloride (CuCl₂)-grafted silica gel, was prepared by a sol–gel process using tetraethoxysilane (TEOS)/3-aminopropyltriethoxysilane (APTES) mixtures. The elemental composition and the chemical combinations of homogeneous sol mixture (HSM) and bamboo were determined via Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy with energy-dispersive X-ray spectrometry (SEM–EDS). The mold resistance of bamboo treated with HSM, alkaline copper quat (ACQ), chromated copper arsenate (CCA), and purified water was characterized by an indoor mold test. The micro-morphology of bamboo treated with HSM was investigated using scanning electron microscopy (SEM). HSM penetrated into the bamboo vessels, and formed xerogels, which was able to coordinate copper(II) cations. SEM–EDS investigations suggest that Si–O–Cu linkages may be formed through an exchange reaction between silanol groups and copper complexes. The bamboo samples treated with HSM showed highly efficient mold resistance due to a good penetration of HSM. Furthermore, no fungal hyphae were found in the structure of HSM-treated bamboo after a 5-week mold test. The copper complexes grafted to silica gel developed in this work provide an efficient antifungal agent for a wide range of potential applications in bamboo protection.

In this research, a urea–formaldehyde (UF) resin was modified with nanocrystalline cellulose (NCC) and nanofibrillated cellulose (CNF), and the properties of the modified resin were comprehensively evaluated by combining the techniques of infrared spectroscopy (FTIR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). The results showed that (1) the introduction of NCC and CNF significantly changed the hydrogen bonding network of the UF resin, in which CNF enhanced the internal hydrogen bonding of the resin through its long-chain structure and elevated the cross-linking density. NCC increased the crystallinity of the resin, while CNF enhanced the overall performance of the resin by improving its dispersion. (2) The composite curing agent system significantly reduced the curing temperature of the resin, resulting in a more homogeneous and efficient curing reaction, and the CNF-modified UF exhibited better thermal stability. (3) The addition of NCC and CNF significantly improved the dry and water-resistant bonding strengths of the resins. In addition, the use of complex curing agent further enhanced the bonding strength, especially in the CNF-modified system; the addition of complex curing agent increased the dry bonding strength to 1.60 MPa, and the water-resistant bonding strength reached 1.13 MPa, which showed a stronger cross-linking network and structural stability. (4) The addition of NCC and CNF led to a significant reduction in the free formaldehyde content of UF resins, resulting in respective levels of 0.17% and 0.14%. For plywood bonded with the CNF-modified UF resin, formaldehyde emissions were measured at 0.35 mg/L, which were markedly lower than the 0.54 mg/L of the unmodified sample. This further highlights CNF’s effectiveness in minimizing formaldehyde release. (5) Overall, CNF is superior to NCC in improving the thermal stability, bonding strength, water resistance, formaldehyde release, and overall performance of the resin. The use of complex curing agents not only optimizes the curing process of the resin but also further enhances the modification effect, especially for CNF-modified resins, which show more significant performance advantages.