The surrounding rock during a coal mine excavation is prone to significant engineering disasters such as considerable deformation and rock bursts. Pressure release can improve the stress field of a deep rock mass and prevent the occurrence of dangers such as roadway collapse and coal and gas outbursts. This paper uses the ANSYS 19.0/LS-DYNA finite element software to simulate the crush area and fracture zone of a detonation charge with different diameters under in situ stress. The stability of the surrounding rock was analyzed based on the impact stress and velocity, and was verified by field tests. The research results show that the blasting load primarily affects the damaged area near the borehole, while the in situ stress affects far-field crack propagation. The crack propagates in the direction of high surrounding rock pressure. When the uncoupling index is 1.5, the impact pressure of a 60 mm diameter cartridge is eight times that of a 20 mm diameter cartridge. The impact speed can reach two times that of the 20 mm diameter cartridge. The high-energy event at the roof is transferred to the front of the working face, the distribution is no longer concentrated, and a better pressure-relief blasting effect is achieved. The research results can help guide the prevention and control measures of rock bursts and other mining disasters.

Aiming at the problem of displacement of collapse direction caused by the impact of the high-rise reinforced concrete chimney in the process of blasting demolition, combined with the monitoring methods such as high-speed photography observation, piezoelectric ceramic sensor, and blasting vibration monitor, the impact process of the 180 m high chimney was comprehensively analyzed. The results show that the chimney will experience multiple ‘weight loss’ and ‘overweight’ effects during the sit-down process, inducing compressive stress waves in the chimney. When the sit-down displacement is large, the broken reinforced concrete at the bottom can play a significant buffering effect, and the ‘overweight’ effect gradually weakens until the sit-down stops. The stress of the inner and outer sides of the chimney wall is obviously different in the process of collapsing and touching the ground. The waveform of the monitoring point of the piezoelectric ceramic sensor is divided into three stages, which specifically characterizes the evolution process of the explosion load and the impact of the chimney. The vibration induced by explosive explosion is mainly high-frequency vibration above 50 Hz, the vibration induced by chimney collapse is mainly low-frequency vibration below 10 Hz, and the vibration characteristics are obviously different. In the process of blasting demolition and collapse of high-rise reinforced concrete chimney, due to the impact of sitting down, the wall of the support tube is subjected to uneven force, resulting in the deviation of the collapse direction. In practical engineering, the control measures of chimney impact, blasting vibration, and collapse touchdown vibration should be fully strengthened to ensure the safety of the protection target around the blasting demolition object.

The nature of the fracture and fragmentation processes in concrete medium under blast loading is the transformation of the medium from continuum to discontinuity. Coupled with the significant rate correlation of concrete medium, its mechanical behavior presents a high degree of complexity. When tackling this problem, the finite element method (FEM) frequently encounters problems such as grid distortion and even negative volume, whereas the material point method (MPM) can efficiently avoid these problems. Furthermore, the original Holmquist-Johnson-Cook (HJC) model does not take the segmented characteristics of the calculation function for the dynamic increasing factor into consideration. As a result, in this article, first, the calculation function for the dynamic increasing factor in the HJC model was modified by the Split-Hopkinson Pressure Bar (SHPB) experiment, and an improved HJC model was proposed; second, an MPM simulation program was developed, and the improved HJC concrete model was embedded into the simulation program; and finally, the simulation program was verified by numerical examples, and the results show that the developed simulation program can better simulate the fracture and fragmentation process of the concrete medium under blast loading, especially the pulverization characteristics of the medium in the near zone of the load.

To quantitatively describe the damage degree and failure process of the cemented backfill (CB) under dynamic loading, this paper performed numerical split Hopkinson pressure bar (SHPB) impact experiments on CB samples using the ANSYS/LS-DYNA. The damage pattern and failure process of CB samples with four mix ratios (cement-to-sand (c/s) ratios of 1:4, 1:6, 1:8, and 1:10) at different impact velocities (v) (1.5, 1.7, 1.8, and 2.0 m/s) were numerically investigated using the micro-crack density method to define the damage variable (d). The results revealed that the use of a waveform shaper in the numerical simulation yielded a more ideal rectangular wave to ensue uniform stress distribution across the sample’s plane without stress concentration. Numerical simulations effectively depicted the dynamic failure process of the CB, with the overall failure trend exhibiting edge spalling followed by the propagation and interconnection of internal cracks. When the v increased from 1.7 m/s to 1.8 m/s, the d increased by more than 10%. As the v increased from 1.5 m/s to 2.0 m/s, the d for c/s ratios of 1:4, 1:6, 1:8, and 1:10 ranged from 0.238 to 0.336, 0.274 to 0.413, 0.391 to 0.547, and 0.473 to 0.617, respectively. A significant “leap” phenomenon in damage was observed when the c/s ratio changed from 1:6 to 1:8.

The nature of the fracture and fragmentation process of concrete medium under blast loading is the transformation process of the medium from continuum to discontinuity, coupled with the significant rate correlation of concrete medium, its mechanical behavior presents a high degree of complexity. Problems such as grid distortion and even negative volume are often encountered in the finite element method and others when solving this problem, while the material point method can effectively avoid these problems. In addition, the widely used HJC concrete constitutive model does not take into account the segmented characteristics of the calculation function for dynamic increasing factor. Therefore, in this paper, firstly, the calculation function for dynamic increasing factor in the HJC concrete model is modified by SHPB experiment, and the improved HJC concrete model is proposed; secondly, the material point method simulation program is developed, and the improved HJC concrete model is embedded into the simulation program; finally, the simulation program is verified by numerical examples, and the results show that the developed simulation program can better simulate the fracture and fragmentation process of concrete medium under blast loading, especially the pulverization characteristics of the medium in the near zone of the load.

In a complex urban environment, the impact of building demolitions by blasting on the structural integrity of nearby metro tunnels is critical. This study systematically analyzed the blasting and demolition process of a building adjacent to a metro tunnel using various monitoring methods, including blasting vibration, dynamic strain, deformation and settlement, pore water pressure, and displacement. The results indicate that the metro tunnel’s vibration response can be divided into four stages: notch blasting, notch closure, overall collapse impact, and auxiliary notch blasting. The most significant impact on the tunnel segments occurred during the building’s ground impact phase, with a peak particle velocity of 0.57 cm/s. The maximum tensile and compressive stresses induced in the tunnel segments did not exceed 0.4 MPa, well within the safety limits. Displacement and settlement changes in the tunnel structure were less than 1 mm, far below the warning threshold. Additionally, blasting vibrations significantly affected the pore water pressure in the surrounding soil. However, fluctuations caused by ground impact vibrations were minimal, and the pore water pressure quickly returned to its initial level after the blasting concluded. Throughout the process, no adverse effects on the metro tunnel structure were observed.