Henry Samir Vanegas

Dr. Henry Samir Vanegas


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2019 in Applied Surface Science
Verified
Journal Article
Closed access
HVHenry Samir Vanegas
Henry Samir Vanegas
SVS. Calderon V
S. Calderon V
JOJ.E. Alfonso O
J.E. Alfonso O
JFJ.J. Olaya F
J.J. Olaya F
PFP.J. Ferreira
P.J. Ferreira
Sandra CarvalhoSandra Carvalho
Sandra Carvalho

31 May 2022 in Coatings
Verified
Journal Article
Open access
PDF file
CMClaudia P. Mejía
Claudia P. Mejía
HVHenry Samir Vanegas
Henry Samir Vanegas
JOJhon Jairo Olaya
Jhon Jairo Olaya
The formation of nanostructured transition metal nitride coatings by introducing a small amount of silver (Ag) content has been proven to be a good strategy for enhancing the physical properties of these materials. In this investigation, ZrN coatings with different Ag contents were deposited on an AISI 316L substrate using the DC reactive magnetron sputtering technique. The influence of the silver on the chemical composition, morphology, and microstructure was investigated using energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The functional properties, specifically the corrosion resistance and the optical reflectance of the deposited coatings, were investigated using electrochemical impedance spectroscopy (EIS) and UV-Visible-NIR, respectively. The results showed the formation of two nanocrystalline phases, fcc-ZrN and metallic fcc-Ag. On the surface of the deposited coatings, homogeneously distributed silver nanoparticles were observed, and they increased with the Ag atomic content. The chemical composition on the surface showed evidence of the formation of oxides, such as Zr-O and Zr-O-N, before and after the corrosion tests. The corrosion resistance of the AISI 316L substrate and the coatings was improved with the incorporation of Ag, and the optical reflectance increased with increasing the Ag content. Finally, this work investigated the effect of the incorporation of silver into a ZrN matrix for potential use as optical protective coatings.

1 September 2019 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
HVH S Vanegas
H S Vanegas
JEJose Edgar
Jose Edgar
JOJhon Jairo Olaya
Jhon Jairo Olaya
HVHenry Samir Vanegas
Henry Samir Vanegas

26 June 2023 in Coatings
Verified
Journal Article
Open access
PDF file
HVHenry Samir Vanegas
Henry Samir Vanegas
SCSebastian Calderon
Sebastian Calderon
JEJose Edgar
Jose Edgar
JOJhon Jairo Olaya
Jhon Jairo Olaya
Sandra CarvalhoSandra Carvalho
Sandra Carvalho
The functional properties of the transition-metal nitride coatings can be modified by adding noble metals such as silver. The incorporation of these elements has been demonstrated to be a good strategy for improving the electrical, optical, and mechanical responses of transition-metal nitride coatings. In this investigation, we report the production of Ag-ZrSiN coatings with varying silver atomic contents, deposited using pulsed-DC reactive magnetron sputtering. The effect of the incorporation of silver on the microstructure, the morphology, and the optical and electrical properties was investigated. The results revealed a nanocomposite structure of Ag-ZrSiN with nc-Ag/nc-ZrN embedded in an amorphous SiNx phase. The electrical resistivity decreased upon the incorporation of Ag from 77.99 Ω·cm to 0.71 Ω·cm for 0.0 and 12.0 at.% of Ag, respectively. A similar decreasing trend was observed in the transmittance spectra of the coatings as the silver content increased. For the Ag-ZrSiN coating, the transmittance values decreased within the wavelength range of 2500–630 nm and then remained constant down to 300 nm, at about 13.7%. Upon further increase of the silver concentration up to 12 at.%, the transmittance values continued to decrease between 2500 and 630 nm, reaching approximately zero at 630 nm, indicating that the coating becomes opaque within that spectral range.

1 June 2016 in Materials Express
Verified
Journal Article
Closed access
HVHenry Samir Vanegas
Henry Samir Vanegas
MPManuel Pinzón
Manuel Pinzón
JAJose E. Alfonso
Jose E. Alfonso
JOJhon J. Olaya
Jhon J. Olaya
CPC. Pineda-Vargas
C. Pineda-Vargas

4 October 2023 in Metals
Verified
Journal Article
Open access
PDF file
AJAndrés Felipe Ordóñez Jiménez
Andrés Felipe Ordóñez Jiménez
HVHenry Samir Vanegas
Henry Samir Vanegas
CMCarlos Mauricio Moreno
Carlos Mauricio Moreno
JOJhon Jairo Olaya
Jhon Jairo Olaya
YTYaneth Pineda Triana
Yaneth Pineda Triana
CrAlTiN-Si coatings have demonstrated their ability to prolong the operational life and improve the performance of cutting tools, primarily attributable to their exceptional mechanical, thermal, and tribological properties. Consequently, this investigation focused on the deposition of CrAlTiN-Si coatings utilizing the high-power impulse magnetron sputtering (HiPIMS) technique. The chemical composition, morphology, and microstructure of these coatings, as well as their mechanical and tribological properties, were investigated. The obtained results revealed that the incorporation of silicon into the CrAlTiN matrix significantly influenced the chemical composition, microstructure, and mechanical properties of the coatings. Specifically, silicon contents ranging from 0 to 1.0 at.% led to the formation of a face-centered cubic (fcc) solid solution within the coatings, resulting in a reduction in the lattice parameter from 0.412 nm to 0.409 nm. However, when the silicon content reached 1.9 at.%, a nanocomposite phase comprising an fcc solid solution of CrAlTiSiN and an amorphous phase of SiNx was observed, along with an increase in the lattice parameter from 0.409 nm to 0.413 nm. An XPS analysis confirmed the presence of oxides in all the coatings, but only the sample with a silicon content of 1.9 at.% showed the presence of Si-N bonds. Furthermore, all the coatings exhibited a distinctive cauliflower-type morphology. The nano-hardness testing demonstrated that the incorporation of silicon resulted in coatings with high nano-hardness values, from 20.0 GPa for the sample without silicon to 22.2 GPa when the silicon content was 1.9 at.%. Moreover, as the Si content increased, the presence of silicon contributed to enhancements in the toughness and fracture resistance of the coating.