Andrés Felipe Ordóñez Jiménez

Mr. Andrés Felipe Ordóñez Jiménez

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 December 2023 in Crystals
Verified
Journal Article
Open access
PDF file
LTLUIS CARLOS ARDILA TELLEZ
LUIS CARLOS ARDILA TELLEZ
RDR. Dueñas
R. Dueñas
Giovany Orozco-HernándezGiovany Orozco-Hernández
Giovany Orozco-Hernández
JOJhon Jairo Olaya
Jhon Jairo Olaya
AJAndrés Felipe Ordóñez Jiménez
Andrés Felipe Ordóñez Jiménez
YTYaneth Pineda Triana
Yaneth Pineda Triana
In this work, nanostructured TiAlCrN coatings were deposited on a WC-Co substrate using a co-sputtering process varying the silicon composition on the coatings. The influence of silicon content on the mechanical, chemical, and tribological performance of the coatings was studied. The hardness increases from 11 to 16 GPa with the Si content; also, Young’s modulus increases from 260 to 295 GPa. The H/E ratio, which is a measure of materials’ ability to take the strain before deformation, is also increased with the increase in Si content, suggesting increased toughness. XPS analysis reveals that the coatings present titanium, aluminum, chromium, and silicon nitrides. The tribological behavior of the coatings was conducted through ball-on-disc tests, in which the results show that the coefficients of friction range from 0.15 to 0.55, with the lowest for the samples with the highest Si content. This behavior is benefited by the formation of oxynitride species, identified by XPS, which acts as lubricating layers and diffusion barriers. TiAlCrSixN coating presents a potential application for severe wear owing to its tribological performance.

4 October 2023 in Metals
Verified
Journal Article
Open access
PDF file
AJAndrés Felipe Ordóñez Jiménez
Andrés Felipe Ordóñez Jiménez
HVHenry Samir Vanegas
Henry Samir Vanegas
CMCarlos Mauricio Moreno
Carlos Mauricio Moreno
JOJhon Jairo Olaya
Jhon Jairo Olaya
YTYaneth Pineda Triana
Yaneth Pineda Triana
CrAlTiN-Si coatings have demonstrated their ability to prolong the operational life and improve the performance of cutting tools, primarily attributable to their exceptional mechanical, thermal, and tribological properties. Consequently, this investigation focused on the deposition of CrAlTiN-Si coatings utilizing the high-power impulse magnetron sputtering (HiPIMS) technique. The chemical composition, morphology, and microstructure of these coatings, as well as their mechanical and tribological properties, were investigated. The obtained results revealed that the incorporation of silicon into the CrAlTiN matrix significantly influenced the chemical composition, microstructure, and mechanical properties of the coatings. Specifically, silicon contents ranging from 0 to 1.0 at.% led to the formation of a face-centered cubic (fcc) solid solution within the coatings, resulting in a reduction in the lattice parameter from 0.412 nm to 0.409 nm. However, when the silicon content reached 1.9 at.%, a nanocomposite phase comprising an fcc solid solution of CrAlTiSiN and an amorphous phase of SiNx was observed, along with an increase in the lattice parameter from 0.409 nm to 0.413 nm. An XPS analysis confirmed the presence of oxides in all the coatings, but only the sample with a silicon content of 1.9 at.% showed the presence of Si-N bonds. Furthermore, all the coatings exhibited a distinctive cauliflower-type morphology. The nano-hardness testing demonstrated that the incorporation of silicon resulted in coatings with high nano-hardness values, from 20.0 GPa for the sample without silicon to 22.2 GPa when the silicon content was 1.9 at.%. Moreover, as the Si content increased, the presence of silicon contributed to enhancements in the toughness and fracture resistance of the coating.