Li Yin

Li Yin


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 March 2024 in Sensors
Verified
Journal Article
Open access
PDF file
AJAiting Jia Jia
Aiting Jia Jia
YLYifang Luo
Yifang Luo
BHBo Hong
Bo Hong
XLXiangwen Li
Xiangwen Li
LYLi Yin
Li Yin
MLMina Luo
Mina Luo
Droplet transfer frequency is a decisive factor in welding quality and efficiency in gas tungsten arc welding (GTAW). However, there still needs to be a monitoring method for droplet transfer frequency with high precision and good real-time performance. Therefore, a real-time monitoring method for droplet transfer frequency in wire-filled GTAW using arc sensing is proposed in this paper. An arc signal acquisition system is developed, and the wavelet filtering method filters out noise from the arc signal. An arc signal segmentation method—based on the OTSU algorithm and a feature extraction method for droplet transition based on density-based spatial clustering of applications with noise (DBSCAN)—is proposed to extract the feature signal of the droplet transition. A new conception of droplet transition uniformity is proposed, and it can be used to monitor the weld bead width uniformity. Numerous experiments for monitoring droplet transfer frequency in real time are conducted with typical welding parameters. This method enables the real-time observation of droplet transfer frequency, and the result shows that the average monitoring error is less than 0.05 Hz.

14 September 2023 in Coatings
Verified
Journal Article
Open access
PDF file
YLYi Li
Yi Li
ZGZhou Zhi gang
Zhou Zhi gang
LYLi Yin
Li Yin
FDFu Dingyao
Fu Dingyao
HJHaiyi Jiang
Haiyi Jiang
FJFuming Jin
Fuming Jin
The two main process parameters of Bobbin tool friction stir welding (BT-FSW) are ω (rotational speed) and v (traverse speed). Both of these factors have a significant effect on heat input, microstructure, and mechanical properties. At present, most studies on friction stir welding adopt the control variable method to study the thermal cycling during the welding process and the mechanical properties of joints, and there are few studies on changing the two process parameters at the same time, because it can be difficult to assess the correlation between heat input and mechanical properties when changing both factors at the same time. In this study, the w/v ratio is defined as the thermal index, which is a characteristic value of heat input. The study uses ABAQUS 6.5 software to establish a BT-FSW CEL (coupled Eulerian–Lagrangian) thermal coupling model. This model explores the relationship between joint thermal cycles, microstructure, and mechanical properties for different w and v values with the same w/v ratio. The results show that increasing rotational and traverse speeds under the same w/v ratio leads to an increase in the peak temperature of the nugget zone (NZ). However, the peak temperature of the thermo-mechanically affected zone (TMAZ) and heat-affected zone (HAZ) remained almost constant. Joint strength was highest at a rotational speed of 750 r/min and a traverse speed of 650 mm/min, with a yield strength of 227 MPa. As rotational and traverse speeds increased, the recrystallized grain content of the NZ showed an increasing trend followed by a decreasing trend. The recrystallized grain content of the advancing side thermo-mechanically affected zone (AS-TMAZ) and retreating side thermo-mechanically affected zone (RS-TMAZ) showed a decreasing trend. Joint hardness had a “W” shaped distribution, with the highest average hardness value found in the NZ.

3 September 2025 in Welding in the World
Verified
Journal Article
Closed access
PDF file
AJAiting Jia
Aiting Jia
DWDongqian Wang
Dongqian Wang
BHBo Hong
Bo Hong
LYLi Yin
Li Yin
XLXiangwen Li
Xiangwen Li
RLRongrong Liu
Rongrong Liu