Dmytro Yelatontsev

Dr. Dmytro Yelatontsev

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2021 in Biomass and Bioenergy
Verified
Journal Article
Closed access
AIAnna Ivanchenko
Anna Ivanchenko
DYDmytro Yelatontsev
Dmytro Yelatontsev
ASAnatoliy Savenkov
Anatoliy Savenkov

22 October 2023 in Journal of Hazardous Materials Letters
Verified
Journal Article
Open access
DYDmytro Yelatontsev
Dmytro Yelatontsev

4 January 2024 in Environmental Challenges
Verified
Journal Article
Open access
AIAnna Ivanchenko
Anna Ivanchenko
DYDmytro Yelatontsev
Dmytro Yelatontsev

2 August 2023 in Alloys
Verified
Journal Article
Open access
PDF file
AMAnatoly Mukhachev
Anatoly Mukhachev
DYDmytro Yelatontsev
Dmytro Yelatontsev
OKOlena Kharytonova
Olena Kharytonova
This article presents the results of studies of the self-propagating high-temperature synthesis (SHS) for obtaining zirconium alloys with niobium by the method of calcium-thermal reduction of nuclear-grade zirconium tetrafluoride in the presence of niobium powder. The optimal heating temperature of the initial charge and the methods of charge mixture with different calcium content were determined. The safety of the SHS process is ensured by the formation of an optimal combustion front of the mixture to remove the released high-pressure gases. A setup for the furnace reduction of zirconium alloys with charge preheating, discharge of molten products into molds of various designs, and control of the time and rate of slag and alloy crystallization has been tested. The required performance of the installation, the degree of transition of zirconium from salt into the alloy, and the purity, structure, and uniformity of the alloy were achieved.

1 January 2021 in TECHNICAL SCIENCES AND TECHNOLOGIES
Verified
Journal Article
Open access
PDF file
AIAnna Ivanchenko
Anna Ivanchenko
DUDniprovsky State Technical University
Dniprovsky State Technical University
OSOleksandr Sokol
Oleksandr Sokol
DYDmytro Yelatontsev
Dmytro Yelatontsev
KLKonstantin Lyapka
Konstantin Lyapka
OROlena Revak
Olena Revak
The work aims to study the process of activation of natural zeolite by inorganic acids, in particular, HNO3and H3PO4to verify their effectiveness when extracting dyes from aqueous media in batch mode.It is proposed to use the method of purification with sorbents modified with mineral acids nitric, hydrochloric, and ortho-phosphate to increase the absorption capacity concerning water-soluble dyes. The analysis of the process of purification and neutralization of dyes in water systems with the help of zeolite of the Sokernyanskoye deposit was carried out experimentally. Chemical activation, which was carried out by the impregnation method, was used to improve the sorption properties. Samples of chemically activated zeolite were obtained. Due toacid activation, Al, K, Na, Ca, Mg, Fe ions are released, which release micro-and mesopores in the sorbent, which increases its porosity and improves sorption properties. The composition of activated natural mineral zeolite with HNO3, HCl, H3PO4acids were characterized. The chemical composition of activated zeolite was determined by X-ray fluorescence.The efficiency of acid-activated zeolite for the extraction of dyes from wastewater was tested. The dependences of the dye extraction process from model solutions using ordinary and acid-activated zeolite have been established. The dye content in the treated wastewater was determined by the photometric method. The kinetic regularities of the dye adsorption process during contact of natural and activated zeolite samples in the time interval every 6 h for 24 h have been established. It was found that the concentration of pollutants varies and depends on the type of acid and has a decisive influence on the obtained chemical properties of the modified samples.It is recommended to use zeolite activated with hydrochloric acid asa natural adsorbent at a dose of 4 g/dm3with a contact time of 24 hours. According to these technological parameters, the dye content in water decreases from 117 mg/dm3to 41 mg/dm3.The obtained results allow to significantly expand the knowledge about the areas of application of natural sorbents in various technological processes.

18 December 2021 in Science and innovation
Verified
Journal Article
Closed access
PDF file
DYDmytro Yelatontsev
Dmytro Yelatontsev
AMAnatoliy Mukhachev
Anatoliy Mukhachev
OIOlena Ivanyuk
Olena Ivanyuk
Introduction. Eco-friendly disposal of food waste, in particular, nutshells and fruit kernels, is an important issue to ensure sustainable nature management. These secondary raw materials are the source of valuable polymeric materials, cellulose and lignin.Problem Statement. IGiven the capacity of the food industry in Ukraine and the amount of waste produced, the development of technologies for processing lignin-cellulose biomass is an important research and practical issue.Purpose. The purpose of this research is to study the adsorption properties of chemically modified biosorbent based on plant materials concerning synthetic dyes of different types and classes; to assess the feasibility of biosorbent production and efficiency of its application in water treatment.Materials and Methods. Lignocellulose sorbent (LCS) has been synthesized from non-wood raw materials by chemical modification with the use of phosphoric acid with the addition of urea in an aqueous media. The Fourier transform infrared and standard methods of plant raw material analysis have been used to determine the physicochemical characteristics of LCS. The adsorption of anionic (methyl orange, alizarin red S, eosin Y), cationic (methylene blue, neutral red), and nonionic (aniline yellow) dyes on LCS from aqueous solution has been studied in the batch mode.Results. The adsorption capacity of LCS towards cationic dyes (47.0–53.3 mg/g) is higher than that of anionic (22.2–36.9 mg/g) and nonionic (4.7 mg/g) ones. The adsorption kinetics have been adequately described by a pseudo-second-order equation. Adsorption of all classes of dyes on LCS is thermodynamically feasible, spontaneous, and endothermic process. The liquid by-product of LCS production contains 15% nitrogen and 10% phosphorus, so it may be used as a fertilizer. Conclusions. The proposed method for processing food waste provides obtaining effective sorbent and liquid NP-fertilizer. LCS removes both cationic and anionic pollutants from water, so it may be considered a promisingbiosorbent for water purification.