Fast response pressure-sensitive paint (PSP) allows optical measurements of pressure fluctuations on a surface with high spatial and temporal resolution. This technique is evaluated for aeroacoustic measurements inside an aeroacoustic wind tunnel (AWT). The AWT is a test rig especially designed for investigating the excitation and propagation of sound under conditions typical for turbomachinery. The aim of this work is to compare the results of sound pressure measurements of tonal sound fields in a circular duct conducted with PSP and microphone arrays in order to assess the applicability of PSP in turbomachinery acoustics applications. A data analysis process is presented, which projects the camera image of the PSP data onto a given surface. To analyze the spatial pressure fluctuations, the PSP data are transformed in the frequency domain using pixel-wise fast Fourier transform. Measurements with a mean Mach number up to 0.109 and 5 kHz excitation frequency are conducted. An acoustic mode generator is used to excite the sound field with specific circumferential mode order. The pressure fluctuations obtained with the PSP measurement visualize the measured acoustic field well and allow early interpretation. The pressures of PSP and microphones are in good agreement; for example, the maximum detected deviation in pressure at 2700 Hz is 30 Pa. A preview on using radial mode analysis to decompose the acoustic field, measured by PSP, into acoustic modes is provided. The results are confirmed by a decomposition using conventional arrays of flush-mounted microphones. Graphical

In this paper, the authors demonstrate the application of a modified Ru(phen)-based temperature-sensitive paint which was originally developed for the evaluation of unsteady aero-thermodynamic phenomena in high Mach number but short duration experiments. In the present work, the modified TSP with a temperature sensitivity of up to −5.6%/K was applied in a low Mach number long-duration test case in a low-pressure environment. For the demonstration of the paint’s performance, a flat plate with a mounted cylinder was set up in the High-Speed Cascade Wind Tunnel (HGK). The test case was designed to generate vortex shedding frequencies up to 4300 Hz which were sampled using a high-speed camera at 40 kHz frame rate to resolve unsteady surface temperature fields for potential heat-transfer estimations. The experiments were carried out at reduced ambient pressure of $p_{\infty }$ = 13.8 kPa for three inflow Mach numbers being $M{a}_{\infty }=[0.3;0.5;0.7]$. In order to enable the resolution of very low temperature fluctuations down to the noise floor of ${10}^{-5}$ K with high spatial and temporal resolution, the flat plate model was equipped with a sprayable carbon nanotube (CNT) heating layer. This constellation, together with the thermal sensors incorporated in the model, allowed for the calculation of a quasi-heat-transfer coefficient from the surface temperature fields. Besides the results of the experiments, the paper highlights the properties of the modified TSP as well as the methodology.

The current study involves numerical and experimental investigations of circular in-line jets impinging on a heated flat plate. The generic configuration is characterized by nine jets, each with a diameter of D = 0.0152 m. The jets are influenced by a self-generating crossflow and are positioned at a nozzle-to-plate distance (H/D) of 5 and a jet pitch (p/D) of 5. The steady Reynolds-averaged Navier–Stokes (RANS) simulations are performed for turbulent jet Reynolds numbers with the in-house CFD code TRACE. The Menter k–ω shear stress transport (SST) model is applied for turbulence modeling and the turbulent scalar fluxes are modeled based on the Reynolds analogy for a constant turbulent Prandtl number. To gain a closer insight into the impingement jet physics, high-resolution near-wall velocity and thermal fields are obtained through large eddy simulations (LESs) and measurements from particle image velocimetry (PIV). Focus is laid on the comparison of RANS results with the LES data and the experimental data. The results exhibit a qualitative similarity between the simulations and the experiments. Furthermore, correlations of the Nusselt number from the literature are used to validate the simulation results.

The temperature-sensitive paint (TSP) method, an optical measurement technique, is used for qualitative skin friction visualizations in a wide variety of aerodynamic applications. One such application is the visualization of the laminar–turbulent boundary-layer transition. Optical access to the surface of interest is mandatory for the measurement system, which consists of scientific cameras and LEDs. But the optical access to the area of interest is often impeded by the available windows of the wind tunnel and the wind tunnel model itself, reducing the field of view and the spatial resolution. In some cases, it is of interest to increase the flexibility of the installation of the optical measurement system by reducing its physical dimensions and placing the installation inside the plenum. The DLR Swept flat PlatE Cross-flow TRAnsition (SPECTRA-A) configuration was selected to investigate the influence of two-dimensional steps on the cross-flow-induced boundary layer transition by means of TSP, as part of the EU project Clean Sky 2. The SPECTRA-A configuration consists of two main elements: a flat plate and a displacement body mounted within a very close distance of each other, creating a narrow gap between the two elements. The surface of interest is the area on the flat plate facing the displacement body. The narrow gap limits the utilization of an external camera setup due to poor optical access. A new optical setup consisting of four miniature CMOS machine-vision cameras and five miniature high-power LEDs was integrated into the displacement body. The characteristics of the camera system were analyzed in laboratory tests, establishing that the miniature CMOS machine-vision cameras are suitable for qualitative TSP skin friction visualizations. This was confirmed by successfully measuring the laminar–turbulent boundary-layer transition on the SPECTRA-A configuration. The integrated TSP system is capable of resolving even small variations of the transition location caused by changing the amplitude of the stationary cross-flow instability. The quality of the TSP visualization with the integrated optical system allows for the measurement of the transition location and the wavelength of the stationary cross-flow instability. Overall, a cost-effective TSP visualization system with small space requirements was developed and tested for future applications in wind tunnel models, model support, or side walls of wind tunnels.