Mathilde Rieu

Dr. Mathilde Rieu

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 January 2012 in Fuel Cells
Verified
Journal Article
Closed access
PDF file
DRD. Rembelski
D. Rembelski
JVJ. P. Viricelle
J. P. Viricelle
LCL. Combemale
L. Combemale
MRMathilde Rieu
Mathilde Rieu

1 November 2016 in Sensors and Actuators B: Chemical
Verified
Journal Article
Closed access
MRMathilde Rieu
Mathilde Rieu
MCMalick Camara
Malick Camara
GTGuy Tournier
Guy Tournier
JVJean-Paul Viricelle
Jean-Paul Viricelle
CPChristophe Pijolat
Christophe Pijolat
DBDanick Briand
Danick Briand

1 June 2011 in Solid State Ionics
Verified
Journal Article
Closed access
RSR. Sayers
R. Sayers
MRMathilde Rieu
Mathilde Rieu
PLP. Lenormand
P. Lenormand
FAF. Ansart
F. Ansart
JKJ.A. Kilner
J.A. Kilner
Stephen SkinnerStephen Skinner
Stephen Skinner

23 September 2019 in Journal of Materials Chemistry C
Verified
Journal Article
Closed access
PDF file
OKOmar Kassem
Omar Kassem
MSMohamed Saadaoui
Mohamed Saadaoui
MRMathilde Rieu
Mathilde Rieu
JVJean-Paul Viricelle
Jean-Paul Viricelle
In recent years, printed and flexible gas sensors have quickly emerged as an innovative area of great interest because of their lightness and low cost. These flexible sensors can be easily integrated into autonomous systems for many applications such as smart food packaging and premature disease detection. In this paper, a novel approach was applied to manufacture a fully inkjet-printed gas sensor on a flexible polymeric foil. A platinum heater and gold electrodes were printed on the top side of the substrate, separated by a thin insulating layer of printed polyimide. An aqueous sol–gel process was adopted to synthesize nanosized SnO2-based sol that guarantees crystallization at 350 °C, which is entirely consistent with the polyimide foil. Then, the sol was transformed into a stable ink and inkjet printed over the gold electrodes. The printability of different inks was optimized to ensure flawless ejection of droplets, and the complex physico-chemical interactions between the inks and different interfaces were controlled to get well-defined patterns with high resolution. Finally, electrical measurements of the printed sensor were performed to characterize the response and sensitivity to different concentrations of ethanol, ammonia and carbon monoxide gases, at a working temperature of 300 °C, in dry and wet air.

1 March 2018 in Sensors and Actuators B: Chemical
Verified
Journal Article
Closed access
MHMohamad Hijazi
Mohamad Hijazi
MRMathilde Rieu
Mathilde Rieu
VSValérie Stambouli
Valérie Stambouli
GTGuy Tournier
Guy Tournier
JVJean-Paul Viricelle
Jean-Paul Viricelle
CPChristophe Pijolat
Christophe Pijolat

1 January 2010 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
MRMathilde Rieu
Mathilde Rieu
RSR. Sayers
R. Sayers
Miguel Ángel Laguna-BerceroMiguel Ángel Laguna-Bercero
Miguel Ángel Laguna-Bercero
Stephen SkinnerStephen Skinner
Stephen Skinner
PLP. Lenormand
P. Lenormand
FAF. Ansart
F. Ansart
Mixed ionic and electronic conducting (MIEC) oxides are promising materials for use as cathodes in solid oxide fuel cells (SOFCs) due to their enhanced electrocatalytic activity compared with electronic conducting oxides. In this paper, the MIEC oxide was prepared by the sol–gel route. Graded cathodes were deposited onto yttria-stabilized zirconia (YSZ) pellets by dip-coating, and electrochemical impedance spectroscopy studies were performed to characterize the symmetrical cell performance. By adapting the slurries, cathode layers with different porosities and thicknesses were obtained. A ceria gadolinium oxide (CGO) barrier layer was introduced, avoiding insulating phase formation and thus reducing resistance polarization of the cathode. A systematic correlation between microstructure, composition, and electrochemical performance of these cathodes has been performed. An improvement of the electrochemical performance has been demonstrated, and a reduction in the area specific resistance (ASR) by a factor of 4.5 has been achieved with a compact interlayer of between the dense electrolyte and the porous cathode layer. The lowest observed ASR of at was obtained from a symmetrical cell composed of a YSZ electrolyte, a CGO interlayer, an intermediate compact layer, a porous electrode layer, and a current collection layer of platinum paste.