In recent years, printed and flexible gas sensors have quickly emerged as an innovative area of great interest because of their lightness and low cost. These flexible sensors can be easily integrated into autonomous systems for many applications such as smart food packaging and premature disease detection. In this paper, a novel approach was applied to manufacture a fully inkjet-printed gas sensor on a flexible polymeric foil. A platinum heater and gold electrodes were printed on the top side of the substrate, separated by a thin insulating layer of printed polyimide. An aqueous sol–gel process was adopted to synthesize nanosized SnO2-based sol that guarantees crystallization at 350 °C, which is entirely consistent with the polyimide foil. Then, the sol was transformed into a stable ink and inkjet printed over the gold electrodes. The printability of different inks was optimized to ensure flawless ejection of droplets, and the complex physico-chemical interactions between the inks and different interfaces were controlled to get well-defined patterns with high resolution. Finally, electrical measurements of the printed sensor were performed to characterize the response and sensitivity to different concentrations of ethanol, ammonia and carbon monoxide gases, at a working temperature of 300 °C, in dry and wet air.
Silicon emerges as a candidate for advancing lithium ion batteries with important roles in various applications ranging from portable electronics to electric vehicles. However, despite its theoretical capacities silicon faces challenges such as unstable cycling and limited rate performance. This thorough review examines developments in improving the electrochemical performance of silicon and graphene within the context of lithium ion batteries. The focus lies on strategies for designing and synthesizing composite materials that incorporate silicon particularly when combined with graphene. Structural aspects like particle size, morphology and porosity are carefully optimized to harness the potential of silicon based anodes and graphene. The review highlights the effects resulting from these tailored design approaches, including key factors such as capacity retention, cycling stability and rate capability of the resulting anode materials. By exploring these design paradigms this review offers a comprehensive perspective on the transformative capabilities of silicon, graphene and silicon/graphene composites. It does not highlights recent advancements but also outlines future directions for innovation and practical applications. This compilation of progress contributes to the understanding of how silicon based anodes, in lithium ion batteries have evolved from small‐scale implementations to catalyzing advancements in energy utilization.
15 June 2023 in ACS Applied Materials & Interfaces
In this work, a flexible tin oxide (SnO2) gas sensor was successfully fabricated by inkjet printing technology. This thin film deposition technique requires the formulation of stable suspensions with specific fluidic properties. Aqueous Sol-gel method was applied to synthesize a stable sol based on tin oxide, then transformed into ink with the appropriate viscosity and surface tension to be printed using a drop-on-demand piezoelectric inkjet printer. Thermal analyses of synthetized sol show that a crystallized structure of SnO2 could be obtained at 350 °C, which is lower than crystallization temperatures of SnO2 previously reported in the literature, and entirely consistent with our plastic substrate. The printed thin-film was then sintered at 350 °C on polyimide foil (Upilex-50S) and characterized as sensor.
Sol based SnO2 precursor was synthetized by aqueous sol-gel route, then transformed into a stable ink with appropriate viscosity and surface tension to be inkjet printed and sintered at relatively moderate temperature. Plastic foil with thickness of 50 μm was selected as substrate for its high thermal resistance and stability (Upilex-50S). Prepared sol and formulated ink were both characterized by analytical techniques; electrical measurements were performed on the printed sensing film to characterize the response to CO gas in different concentrations, at working temperature of 300 °C.
Silicon is a promising anode material for next-generation lithium-ion batteries (LIBs) due to its high theoretical capacity. However, its practical use is hindered by significant volume expansion during charge cycles, which causes poor cycling stability. Intense pulsed light technology offers a solution through rapid, selective heating, enabling nanoscale transformations without damaging substrates. Here, a scalable approach for creating silicon patterns on polymer foils and converting them into nanoscale composite layers under ambient conditions is presented. The use of inkjet printing in conjunction with intense Pulsed Light treatment is demonstrated to generate localized temperatures in excess of 1,940 °C within milliseconds, whilst maintaining the integrity of the polymer substrate. This rapid heating method induces local carbonization of the polymer, thereby converting the Si nanoparticles into a new silicon carbide (SiC) embedded in a few-layer graphene composite electrode. The resulting heterostructure anode exhibits excellent electrochemical performance, improved cycling stability, and enhanced rate capability, positioning it as a promising binder-free silicon anode for next-generation lithium-ion batteries.