Ji-Seon Paek

Prof. Dr. Ji-Seon Paek


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 November 2021 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
Jaehun LeeJaehun Lee
Jaehun Lee
JPJi-Seon Paek
Ji-Seon Paek
SHSongcheol Hong
Songcheol Hong
This article presents two millimeter-wave frequency reconfigurable dual-band CMOS power amplifiers (PAs) for fifth-generation (5G) communications comprising a single-stage dual-band PA and a two-stage dual-band PA for higher gain. The PAs cover multiple 5G communication bands, n257 (26.5–29.5 GHz) and n260 (37–40 GHz), which use reconfigurable transmission line transformers (TLTs) for output, input, and interstage matching networks. These matching networks allow the operating frequency bands to be changed, thereby achieving optimum performance. The integrated mode selection switches in the transformers reconfigure the inductances of the TLTs to cover two frequency bands, which allows the PAs to have small overall chip sizes. These are fabricated in a 28-nm bulk CMOS process. The single-stage dual-band PA achieves 20.2-/19.1-dBm saturated output power ( ${P}_{\text {sat}}$ ), 18.7-/18.6-dBm 1-dB compressed output power ( ${P}_{\text {1 dB}}$ ), and 33.6%/32% peak power-added efficiency (PAE) at 26.5 and 37 GHz, respectively, while occupying a chip area of 0.11 mm 2 . The two-stage dual-band PA achieves 19.1-/19.5-dBm ${P}_{\text {sat}}$ , 17-/17.8-dBm ${P}_{\text {1 dB}}$ , and 31.3%/30.5% PAE at 26.5 and 37 GHz, respectively, while occupying a chip area of 0.165 mm 2 . Both PAs are tested under 64-quadrature amplitude modulation signals with a 100-MHz channel bandwidth. The single-stage PA achieves 14.7- and 12.3-dBm average output powers ( ${P}_{\text {avg}}$ ) with −25.1- and −25-dB error vector magnitudes (EVMs) at 26.5 and 37 GHz, respectively. The two-stage PA achieves 12.3- and 11.6-dBm ${P}_{\text {avg}}$ ’s with −25.3- and −25.1-dB EVMs at 26.5 and 37 GHz, respectively.

21 September 2016 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
JPJi-Seon Paek
Ji-Seon Paek
SLSeung-Chul Lee
Seung-Chul Lee
YYYong-Sik Youn
Yong-Sik Youn
DKDongsu Kim
Dongsu Kim
JCJeong-Hyun Choi
Jeong-Hyun Choi
TCThomas Byunghak Cho
Thomas Byunghak Cho
This paper presents a hybrid supply modulator (SM) with a comprehensive analysis of receiver (RX) band noise in an envelope tracking power amplifier (ET-PA). The designed SM supports both ET mode and average power tracking (APT) mode depending on the PA output power level. In the APT mode, an integrated buck-boost (BB) converter with hysteretic control generates dc supply voltage and its average switching frequency ranges from 1 to 2 MHz. In the ET mode, the bandwidth of SM is determined by a linear amplifier, which has about 30 MHz of signal bandwidth. To improve the ET efficiency, an ac coupling capacitor, with an adaptive offset control, and scaled linear supply are used. The scaled linear supply is provided by the BB converter. To lower the output noise of the SM, a parallel class-AB output buffer and resonance frequency tuning schemes are applied in this paper. For long term evolution 10 MHz with quadrature phase shift keying modulation and 5.8 dB peak-to-average power ratio, the designed SM achieves 82% efficiency at 800 mW output power with a fixed 8 Ω resistor. Adapting the proposed SM to a PA, a 10 dB ET operation dynamic range is achieved while achieving a power added efficiency of 42.6% at 27 dBm PA output power. The measured SM output noise is -137 dBm/Hz at 95 MHz offset with the PA load, and the PA RX band noise is -124 dBm/Hz, which is dominated by the stand-alone PA itself. The chip is implemented with a 130 nm CMOS process and the die size is 5.0 mm2.

2 August 2022 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
JCJeong-Hyun Cho
Jeong-Hyun Cho
DKDong-Kyu Kim
Dong-Kyu Kim
HBHong-Hyun Bae
Hong-Hyun Bae
YLYong-Jin Lee
Yong-Jin Lee
SKSeok-Tae Koh
Seok-Tae Koh
HKHyun-Sik Kim
Hyun-Sik Kim
This article presents a fully integrated multi-phase (MP) buck converter for on-chip power management units A peak-and-valley differential sensing (PVDS) scheme based on a flying capacitor is proposed to evenly balance the multiple inductor currents without significant power overhead even under mismatches in inductances, parasitic series resistances, and control-signal skews among phases. In addition, dynamic re-allocation of on-chip capacitors enables an even more optimal frequency response and output ripple based on the number of activated phases. It also improves the chip area efficiency, resulting in a higher power density. The proposed DLL-based MP clock generation provides high granularity in the phase-shedding control to achieve high efficiency over a wide load range. The proposed fully integrated buck converter using six bond-wire inductors (1 nH) was fabricated in a 28-nm CMOS process. The chip running at a frequency of 400 MHz/phase can finely adjust the number of active phases by an integer step ranging from 1 to 6 through sensing a load current. A maximum power density of 1.23 W/mm $^{2}$ and a peak efficiency of 83.7% were measured. This work achieved an ultra-fast dynamic voltage scaling (DVS) rate of 75 mV/ns.

20 November 2018 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
JPJi-Seon Paek
Ji-Seon Paek
DKDongsu Kim
Dongsu Kim
YCYounghwan Choo
Younghwan Choo
YYYong-Sik Youn
Yong-Sik Youn
JLJongwoo Lee
Jongwoo Lee
TCThomas Byung-Hak Cho
Thomas Byung-Hak Cho
This paper presents a hybrid supply modulator (SM) including a buck-boost (BB) converter, which has wide battery operating range for cellular envelope tracking (ET) applications. The proposed SM supports both ET and average power tracking (APT) mode depending on the power amplifier (PA) output power level. The output voltage swing of SM is boosted up to 4.5 V by the integrated BB converter as a supply of a linear amplifier. The dynamic-controlled BB output increases ET operating range, whose efficiency is higher than that of APT, by scaling down the supply voltage of the linear amplifier according to the PA output power level. A selective supply voltage of a switching amplifier and a reverse current sensing circuit are employed to prevent the reverse current through the power inductor of the switching amplifier. The proposed automatic current ratio controller between the linear amplifier and the switching amplifier provides the robust performance against the battery voltage variation of 3.2-4.6 V. A programmable bias current of the class-AB output buffer and a programmable hysteretic comparator are employed to achieve the optimum efficiency and bandwidth depending on the operating signal bandwidth. Optimal control for low signal bandwidth applications such as voice over Long-Term Evolution (LTE) with the selective notch filter provides the maximum efficiency of 88.2% with -135 dBm/Hz output noise. The proposed SM supports the LTE 20-MHz envelope signal with 78% efficiency at 800-mW output. Adapting the designed SM to frequency-division duplex Band3 radio frequency PA, the implemented ET-PA achieves the power added efficiency of 41.6% at 27-dBm PA output power while achieving -40 dBc of E-UTRA ACLR and -137 dBm/Hz of receiver band noise. The chip is implemented in the 0.13-μm CMOS process, and the die size is 5 mmμ.

7 February 2022 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
JPJi-Seon Paek
Ji-Seon Paek
DKDongsu Kim
Dongsu Kim
JHJae-Yeol Han
Jae-Yeol Han
YCYounghwan Choo
Younghwan Choo
JBJun-Suk Bang
Jun-Suk Bang
JLJongwoo Lee
Jongwoo Lee
This article presents a two-chip supply modulation architecture for efficient RF power amplification using a fully switched-mode supply modulator (SM) and a linear-assisted hybrid SM to support simultaneous transmission on long-term evolution (LTE) and 5G bands. The designed fully switched-mode SM consists of a fast switching buck converter and a slow switching buck converter, and it achieves 88.2% peak efficiency and a low receiver (RX) band noise of −140 dBm/Hz at the SM output. The fully switched-mode SM tracks the envelope of LTE 5-/10-/20-MHz signals with the average switching frequencies of 50/70/120 MHz, respectively. The ET-PA measured using the fully switched-mode SM and LTE band-3 power amplifier module integrated duplexer (PAMiD) saves the dc power consumption of 320 mW at a 23-dBm output power compared to an average power tracking (APT)-PA. The designed 5G new radio (NR) SM consisting of a class-AB linear amplifier (LA) and an interleaved three-level buck–boost converter provides a 160-MHz 3-dB bandwidth to track the envelope of a 100-MHz NR signal. The measured peak SM efficiency is 84.1% at a 3.53-W output power. The measured ET-PA with 5G NR SM and 5G n77 PAMiD achieves an ACLR of −36.9 dBc at a 27.45-dBm output power with a 6-dB peak-to-average-power ratio DFT-spread-OFDM NR 100-MHz quadrature phase shift keying (QPSK) signal. It saves the dc power consumption of 950 mW at a 27-dBm output power compared to APT-PA. An optimal RF power amplifier (RF-PA) supply deployment using the two SMs efficiently supports multiple RF-PA loads while satisfying the dual-transmission requirements of E-UTRAN new radio dual-connectivity (EN-DC) and 5G 100-MHz ET operation. The fully switched-mode SM is implemented in a 130-nm CMOS process, and the die size is 4.0 mm 2 . The 5G NR SM is implemented in a 90-nm CMOS process, and the die size is 6.75 mm 2 .

3 October 2023 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
WKWan Kim
Wan Kim
HSHyun-Gi Seok
Hyun-Gi Seok
GLGeunhaeng Lee
Geunhaeng Lee
SKSinyoung Kim
Sinyoung Kim
JLJae-Keun Lee
Jae-Keun Lee
JKJoonsuk Kim
Joonsuk Kim
This article presents a fully integrated ultrawideband (UWB) system-on-chip (SoC) that complies with IEEE 802.15.4/4z standard, providing precise positioning and secure communication capabilities. The proposed UWB SoC includes a radio frequency (RF) transceiver, a modem, a microcontroller unit (MCU), an eFlash, a power management unit (PMU), clock generation IPs, and peripheral blocks. The RF transceiver integrates RF switches and comprises two transmitters and three receivers. The proposed nonuniform quantization digital-to-analog converter (NQ-DAC) is used in the transmitter to enhance the quality of pulse sidelobe, and a receiver I/Q mismatch estimation technique using a double-sideband (DSB) transmitter as a reference is proposed. The UWB SoC operates in the frequencies at 6.5 GHz (Ch5) and 8 GHz (Ch9), achieving a location estimation precision of a few centimeters. The prototype UWB SoC is fabricated in a CMOS 28-nm process, and the experimental results under base pulse repetition frequencies (BPRFs) 6.81 Mbps show a receiver sensitivity of $-$ 96.1 dBm and a transmitter output peak power of 14.25 dBm, achieving the state-of-the-art performance. The prototype UWB SoC demonstrates the power consumption of 198.6 mW during transmitter operation and 309.7, 442.5, and 528.9 mW for 1-RX, 2-RX, and 3-RX during packet reception. The proposed UWB SoC architecture and techniques provide a practical and efficient solution for IEEE 802.15.4/4z compliant UWB systems.