This paper presents a detailed study on the main parameters and performance evaluation of microjet engines, at take-off regime and at various engine working regimes, based on thermodynamic analysis of a particular engine data library, from different engine manufacturers such as JetCat and AMT Netherlands. The studied engines have the same spool design but different thrust classes ranging from 97 to 1569 N. The particular data library includes engine specifications from catalogs or data sheets as well as our own experimental data from the JetCat P80 microjet engine, obtained using the ET 796 Jet Turbine Module, a complete testing facility for gas turbine education purposes. Various ratios and differences between certain engine main parameters and performances are studied in order to calculate values through which the analyses can be performed. Even if the engines have different thrust classes, the study examines if there are close values of the ratios and differences of parameters, that can be defined as reference parameters through which the engine performance can be compared and evaluated.
The present research focused on studying the mechanical properties of three commercially available thermoplastic-based materials used for the additive manufacturing (AM) fused filament deposition (FFD) method. The scientific motivation for the study was the limited information available in the literature regarding the materials’ properties, the inconsistencies that were recorded by other scientists between the materials’ properties and the technical datasheets and the anisotropic behavior of additively manufactured materials. Thereby, it was considered of great importance to perform an extensive study on several materials’ mechanical properties, such as tensile properties and flexural properties. Three materials were tested, Tough PLA, nGen CF10 and UltraFuse PAHT CF15. The tests consisted of monotonic tensile tests, open-hole tensile tests and three-point bending tests. The tests were assisted also with the use of microscopical investigations. Framed specimens’ configurations with two different raster orientations (90°/0° and −45°/+45°) were manufactured using an in-house-developed 3D printing equipment. The best mechanical performances were recorded for UltraFuse PAHT CF15. The 90°/0° raster orientations ensured the highest tensile, open-hole tensile and flexural strength, regardless of the material type, while the −45°/+45° raster orientations ensured the highest elongation values. The analysis showed the importance of the experimental validation of materials for AM.
The research described in this paper focuses on the development of an innovative unmanned aerial vehicle (UAV) tailored for a specific mission: detecting the acoustic signature emitted by chainsaws, identifying deforestation, and reporting its location for legality assessment. Various calculations were conducted to determine the optimal solution, resulting in the choice of a fixed-wing UAV. A comparative analysis between tri-rotor and quadcopter systems was performed, leading to the selection of the tri-rotor configuration. The primary objective of this study is to design an innovative hybrid UAV concept with key features including a fixed-wing design and integrated VTOL (vertical takeoff and landing) capability in the experimental model. The aircraft has been constructed using advanced materials such as fiber-reinforced polymer composites, manufactured using both conventional and advanced techniques like continuous fiber additive manufacturing and the use of a polymer matrix. Additionally, the aerodynamic configuration is optimized to achieve a cruise speed of approximately 50 km/h and a flight autonomy exceeding 3 h. The UAV has been equipped with payloads for mounting sensors to collect meteorological data, and crucially, the VTOL system has been optimized to vectorize thrust for improved performance during the transition from hover to cruise flight. This paper details the entire manufacturing and assembly process of the drone, covering both the structural framework and associated electrical installations. A dedicated sound detection system is incorporated into the drone to identify chainsaw noise, with the aim of preventing deforestation.
This paper aims to conduct an acoustic analysis through noise measurements of a hybrid propulsion system intended for implementation on a drone, from which the main noise sources can be identified for further research on noise reduction techniques. Additionally, the noise was characterized by performing spectral analysis and identifying the tonal components that contribute to the overall noise. The propelling force system consists of a micro-turboshaft coupled with a gearbox connected to an electric generator. The propulsion system consists of a micro-turboshaft coupled with a gearbox connected to an electric generator. The electric current produced by the generator powers an electric ducted fan (EDF). The engineturbo-engine was tested in free-field conditions for noise generation at different speeds, and for this, an array of microphones was installed, positioned polarly around the system and near the intake and exhaust. Consequently, based on the test results, the acoustic directivity was plotted, revealing that the highest noise levels are at the front and rear of the engine. The noise level at a distance of 1.5 m from the turboengine exceeds 90 dBA at all tested speeds. Spectral analyses of both the far-field acoustic signals (measured with a polar microphone array) and the near-field signals (microphones positioned near the intake and exhaust) revealed that the primary contributors to the overall noise are the micromotor’s compressor, specifically the gas dynamic phenomena in the fan (BPF and 2× BPF). Thus, it was determined that at the intake level, the main noise contribution comes from the high-frequency components of the compressor, while at the exhaust level, the noise mainly originates from the combustion chamber, characterized by low-frequency components (up to 2 kHz). The findings from this study have practical applications in the design and development of quieter drone propulsion systems. By identifying and targeting the primary noise sources, engineers can implement effective noise reduction strategies, leading to drones that are less disruptive in urban environments and other noise-sensitive areas. This can enhance the acceptance and deployment of drone technology in various sectors, including logistics, surveillance, and environmental monitoring.
This paper presents a special analysis study about the gas turbine operating line, and an overall description of a gas turbines project, based on experimental data from two particular applications, in order to convert two different types of aero engines into the same engine configuration. The experimental works were carried out with the aim of converting an Ivchenko AI-20K turboprop and a Rolls-Royce Viper 632-41 turbojet into free turbine turboshaft engines, to be used in marine propulsion, and also to obtain an experimental database to be used in other gas turbine applications. In order to carry out the experimental work, the engines were tested in turbojet configuration, to simulate the free turbine load by using jet nozzles with different geometries of the outlet cross-section. Following the engines’ tests, a series of measured data were obtained, through which it was possible to experimentally determine the operating line of some engine components such as the compressor, turbine, and exhaust jet nozzle. This paper is comprehensive and useful through its scientific and technical guidelines, the operation curves coming in handy in the thermodynamic analysis and testing methodology for researchers dealing with similar applications.
A study on the possibility of integrating a micro-turbogenerator system into a multi-rotor UAV platform was performed along with a performance evaluation of the result. This paper presents the design and development of a micro-turbogenerator system constructed from commercially available components and the associated test bench that was needed to validate the system. The goal of the micro-turbogenerator system was to replace the electrical power source (the batteries) of an experimental UAV. Substituting the electrical power source with a hybrid propulsion system has the potential to enhance the UAV’s endurance and functionality, rendering it more versatile and efficient. The hybrid propulsion system involves the use of a commercially available micro-gas turbine that propels an electric generator, supplying the required electrical power for the UAV’s electric propulsion system. Integrating this micro-turbogenerator system ensures a substantial increase in UAV endurance. The test bench was used to assess the performance of the micro-turbogenerator system and formulate a control law necessary for maintaining a balance between the power generated by the system and the power consumed by the UAV. The developed test bench yielded crucial data, including electric power, generated voltage, generator speed, and power consumption (simulating the UAV in this case). During the testing campaign, the variation in the main physical quantities involved in the command and control of the hybrid propulsion system was registered and analyzed. A total power of 700 W was obtained during the tests, which is the maximum that can be registered for maintaining a power of 25 V.