Hayam abokhasha ali

Dr. Hayam abokhasha ali


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 October 2024 in Metals and Materials International
Verified
Journal Article
Open access
PDF file
AAAhmed H. Awad
Ahmed H. Awad
MSModar Saood
Modar Saood
HAHayam abokhasha ali
Hayam abokhasha ali
AAAhmed W. Abdelghany
Ahmed W. Abdelghany
The utilization of Ti–Mo alloys in biomedical applications has gained attention for use in biomedical applications owing to their non-toxicity, reasonable cost, and favorable properties. In the present study, Ti–12Mo–6Zr and Ti–15Mo–6Zr alloys were prepared using elemental blend and mechanical alloying techniques. The effect of alloying elements Mo and Zr of Ti–Mo alloy, as well as the effect of fabrication techniques of Ti–Mo–Zr trinary alloys, were investigated. Thermodynamic calculations supported by CALPHAD analysis revealed that the addition of Zr increases lattice distortion, which contributes to enhancing the strength. Conversely, adding Mo decreases the enthalpy, facilitating improved mixing and solid solution formation. The as-sintered samples were characterized by X-ray diffraction, optical microscope, and scanning electron microscopy, and their microhardness, compressive, and corrosion behavior were investigated. Among all the investigated alloys, Ti–15Mo–6Zr alloy prepared by the mechanical alloying technique, milled for six hours at 300 rpm, compacted at 600 MPa, and sintered at 1250 ℃, shows good comprehensive mechanical properties with a preferable compressive strength (− 1710 MPa) and hardness (396 HV5), as well as the lowest wear rate (0.69%) and corrosion rate (0.557 × 10–3 mm/year). This can be related to the solid solution strengthening and relative density, together with dispersion and precipitation strengthening of the α phase. Remarkably, the combination of high mechanical and corrosion properties can be achieved by tailoring the content of the α phase, controlling the density, and providing new fabricating techniques for β Ti alloys. Graphical Abstract

1 July 2023 in Materials
Verified
Journal Article
Open access
PDF file
HAHayam abokhasha ali
Hayam abokhasha ali
Mohamed M. El-Sayed Seleman El-NagarMohamed M. El-Sayed Seleman El-Nagar
Mohamed M. El-Sayed Seleman El-Nagar
ABAshraf Bakkar
Ashraf Bakkar
IAIbrahim Albaijan
Ibrahim Albaijan
Mohamed Mohamed Zaky AhmedMohamed Mohamed Zaky Ahmed
Mohamed Mohamed Zaky Ahmed
KIKhaled M Ibrahim
Khaled M Ibrahim
Thermal expansion measurements were used to characterize phase transformations in metastable β-Ti alloys (Ti15MoxSi) without and with various Si additions (where x = 0, 0.5, 1.0, 1.5, and 2 in wt.%) during linear heating at two heating rates of 5 and 10 °C/min up to 850 °C. For this study, five alloys were developed and examined in terms of their presence phases, microstructures, and starting and final transformation temperatures. According to the results, all of the as-cast samples primarily include an equiaxed β-Ti phase. The influence of phase transformation on the material dimensions was discussed and compared with the variations in Si contents. The transformation was investigated using a dilatometric technique for the developed alloys during continuous heating and cooling. The dilatometric curve of heating revealed two distinct reflection points as the heating temperature increased. The starting transformation temperature (Ts) to obtain the ω-phase was reported at 359 °C without Si addition; whereas the final transformation temperature (Tf) of the dissolution of α-phase was obtained at 572 °C at a heating rate of 10 °C/min. At 2 wt.% Si, the first derivative curves reported Ts and Tf transforming temperatures of 314–565 °C (at a 5 °C/min heating rate) and 270–540 °C (at a 10 °C/min heating rate), respectively. The Ts and Tf transforming temperatures were significantly decreased with Si additions, which decreased the β-transus temperature. Moreover, the thermal expansion coefficient curves of the investigated alloys without and with 2 wt.% Si were studied. The transformation heating curves have an S-shaped pattern, according to the results.

8 November 2023 in Metals
Verified
Journal Article
Open access
PDF file
Mohamed M. El-Sayed Seleman El-NagarMohamed M. El-Sayed Seleman El-Nagar
Mohamed M. El-Sayed Seleman El-Nagar
Sabbah AtayaSabbah Ataya
Sabbah Ataya
HAHayam abokhasha ali
Hayam abokhasha ali
Barun HaldarBarun Haldar
Barun Haldar
NANaser A. Alsaleh
Naser A. Alsaleh
KIKhaled M Ibrahim
Khaled M Ibrahim
The durability of a metallic biomaterial to withstand weight loss is a key factor in determining its service life and performance. Therefore, it is essential to create biomaterials with high wear resistance to ensure the biomaterial has a long service life. Thus, this study aims to explore the dry and wet sliding wear characteristics of the developed Ti-15Mo-xSi as-cast alloys (where x equals 0, 0.5, 1, 1.5, and 2 wt.%) in order to assess the impact of the Si addition on the microstructure, mechanical properties, and wear resistance and to consider them for biomedical applications. The wear experiments were conducted using a pin-on-desk wear testing machine at a load of 20 N and a sliding distance of 1000 m with and without applying simulated body fluid (SBF). Different techniques were utilized in the evaluation of the developed Ti-15Mo-xSi alloys. The results showed that significant grain refining was attained with the Si addition. The hardness, compressive strength, and wear resistance of the Ti-15Mo-xSi as-cast alloys increased with the increase in Si content. The Ti-15Mo-2Si as-cast alloy exhibited the highest dry and wet wear resistance of all the Ti-15Mo-xSi alloys. The worn surfaces were investigated, the roughness and main features were reported, and the wear mechanisms were also discussed.

5 May 2026 in RSC Advances
Verified
Journal Article
Open access
PDF file
ABAshraf Bakkar
Ashraf Bakkar
Mohamed M. El-Sayed Seleman El-NagarMohamed M. El-Sayed Seleman El-Nagar
Mohamed M. El-Sayed Seleman El-Nagar
Sabbah AtayaSabbah Ataya
Sabbah Ataya
HRHagar A. Reyad
Hagar A. Reyad
KIKhaled M Ibrahim
Khaled M Ibrahim
HAHayam abokhasha ali
Hayam abokhasha ali
Titanium (Ti) and its alloys are preferred biomaterials for orthopedic and dental implants due to their excellent biocompatibility and corrosion resistance. However, the development of non-toxic β-Ti alloys with low elastic modulus, high strength, and superior corrosion resistance remains a key challenge for long-term implant applications. The Ti-15Mo alloy is a promising candidate due to its good biocompatibility and mechanical properties. This study investigates the influence of silicon additions (0–2 wt%) on the microstructure, mechanical properties, and corrosion behavior of as-cast Ti-15Mo-xSi alloys for biomedical applications. The corrosion behavior was investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) at 37 °C in simulated body fluid (SBF). Moreover, the passive films formed on the surfaces of the alloys were examined using X-ray photoelectron spectroscopy analysis (XPS). The results indicated that Si additions refined the grain size and improved the mechanical properties. All alloys spontaneously formed a stable passive oxide layer. Crucially, the corrosion resistance improved systematically with Si content, as evidenced by a nobler open-circuit potential, a lower corrosion current density (reaching ∼1.03 × 10−7 A cm−2 for the 2 wt% Si alloy), and a higher passive film resistance. XPS confirmed that the passive film is primarily composed of TiO2, with the superior performance of the 2 wt% Si alloy attributed to a denser, more compact oxide layer enriched with protective silicon oxides. The Ti-15Mo-2Si alloy, combining high strength and exceptional corrosion resistance, emerges as a highly promising candidate for load-bearing surgical implants.