Ahmed W. Abdelghany

Dr. Ahmed W. Abdelghany

Faculty of Engineering Ain-Shams Uni, Cairo, Al Qāhirah, Egypt
+1
orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 August 2022 in Journal of Alloys and Compounds
Verified
Journal Article
Open access
AAAhmed W. Abdelghany
Ahmed W. Abdelghany
MJMatias Jaskari
Matias Jaskari
AHAtef S. Hamada
Atef S. Hamada
AJAntti Järvenpää
Antti Järvenpää
HEHassan A. El-Hofy
Hassan A. El-Hofy
MGMohamed Abdel-Hady Gepreel
Mohamed Abdel-Hady Gepreel

16 November 2019 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Closed access
PDF file
AAAhmed H. Awad
Ahmed H. Awad
AAAhmed W. Abdelghany
Ahmed W. Abdelghany
AEAyman A. Abd El-Wahab
Ayman A. Abd El-Wahab
RERamadan El-Gamasy
Ramadan El-Gamasy
MAMohamed Hazem Abdellatif
Mohamed Hazem Abdellatif

21 October 2024 in Metals and Materials International
Verified
Journal Article
Open access
PDF file
AAAhmed H. Awad
Ahmed H. Awad
MSModar Saood
Modar Saood
HAHayam abokhasha ali
Hayam abokhasha ali
AAAhmed W. Abdelghany
Ahmed W. Abdelghany
The utilization of Ti–Mo alloys in biomedical applications has gained attention for use in biomedical applications owing to their non-toxicity, reasonable cost, and favorable properties. In the present study, Ti–12Mo–6Zr and Ti–15Mo–6Zr alloys were prepared using elemental blend and mechanical alloying techniques. The effect of alloying elements Mo and Zr of Ti–Mo alloy, as well as the effect of fabrication techniques of Ti–Mo–Zr trinary alloys, were investigated. Thermodynamic calculations supported by CALPHAD analysis revealed that the addition of Zr increases lattice distortion, which contributes to enhancing the strength. Conversely, adding Mo decreases the enthalpy, facilitating improved mixing and solid solution formation. The as-sintered samples were characterized by X-ray diffraction, optical microscope, and scanning electron microscopy, and their microhardness, compressive, and corrosion behavior were investigated. Among all the investigated alloys, Ti–15Mo–6Zr alloy prepared by the mechanical alloying technique, milled for six hours at 300 rpm, compacted at 600 MPa, and sintered at 1250 ℃, shows good comprehensive mechanical properties with a preferable compressive strength (− 1710 MPa) and hardness (396 HV5), as well as the lowest wear rate (0.69%) and corrosion rate (0.557 × 10–3 mm/year). This can be related to the solid solution strengthening and relative density, together with dispersion and precipitation strengthening of the α phase. Remarkably, the combination of high mechanical and corrosion properties can be achieved by tailoring the content of the α phase, controlling the density, and providing new fabricating techniques for β Ti alloys. Graphical Abstract

23 June 2025 in Materials Science and Engineering: A
Verified
Journal Article
Open access
HHHassan Hosseinlou
Hassan Hosseinlou
MSMohsen Shakeri
Mohsen Shakeri
AAAhmed W. Abdelghany
Ahmed W. Abdelghany
MJMatias Jaskari
Matias Jaskari
AJAntti Järvenpää
Antti Järvenpää
Atef Saad Saad HamadaAtef Saad Saad Hamada
Atef Saad Saad Hamada

23 June 2020 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
AAAhmed W. Abdelghany
Ahmed W. Abdelghany
SESally Elkatatny
Sally Elkatatny
MGMohamed Abdel-Hady Gepreel
Mohamed Abdel-Hady Gepreel
In the present study, two newly developed non-equiatomic high entropy Al10Cr12Mn28Fe(50-x)Ni(x) alloys (x= 20 & 15 at%, namely: Ni20 & Ni15, respectively) are investigated. The studied HEAs were designed based on thermodynamic principles to maintain high ductility and improve strength. Ingots were prepared using arc-melting then microstructure examinations and mechanical properties for the as-cast alloys were done. The mechanical properties were enhanced for the as-cast material, compared with previously introduced HEAs of the same system, namely Al5Cr12Mn28Fe35Ni20, (Al5) and Al10Cr12Mn23Fe35Ni20, (Al10). Al10Cr12Mn28Fe30Ni20 (Ni20) HEA generally shows the highest compressive yield strength which was improved by ∼7% when compared with previously introduced Al10.

5 August 2025 in Materials & Design
Verified
Journal Article
Open access
Mahmoud KhedrMahmoud Khedr
Mahmoud Khedr
KEKhaled Elkhouly
Khaled Elkhouly
MJMatias Jaskari
Matias Jaskari
MFMikko A.J Finnilä
Mikko A.J Finnilä
AJAntti Viljami Järvenpää
Antti Viljami Järvenpää
AAAhmed W. Abdelghany
Ahmed W. Abdelghany