Tests were carried out to develop and manufacture various types of auxetic dowels using 3D printing technology. These dowels were then used to connect L-type corner joint specimens for case furniture, and their strength and stiffness were analyzed through experimental, theoretical, and numerical means. In the scope of the study, eight different types of auxetic dowels including two inclusion types, two inclusion sizes, and two dowel hole diameters, as well as a reference non-auxetic dowel, were designed. Accordingly, a total of 180 specimens that included 10 replications for each group were tested; 90 were tested under tension and the remaining 90 were tested under compression. The results demonstrated that the assembly force required for the corner joints connected with auxetic dowels was significantly lower compared to non-auxetic dowels. Furthermore, the numerical and theoretical analyses yielded similar outcomes in this study. Both analyses revealed that the dowels used to connect the corner joints experienced substantial stresses during mounting and bending, ultimately leading to their failure. Upon concluding the test results, it was observed that the corner joints connected with dowels featuring rectangular inclusions exhibited superior performance when compared to those with triangular inclusions. In light of these findings, it can be concluded that further enhancements are necessary for auxetic dowels with rectangular inclusions before they can be utilized as alternative fasteners for traditional dowels.
This study aimed to assess the cyclic load capacity of wooden chairs and subsequently categorize them based on their performance. A diverse selection of chair models was randomly procured from commercial markets. These chairs underwent performance testing, utilizing the cyclic stepped increasing loading method, with adherence to the standards set forth by the American Library Association Technology Reports (ALA). The study evaluated 315 chairs, encompassing 21 chair models. Each chair model underwent five replications of testing across three different loading directions. The resulting dataset of numerical values was subjected to statistical analyses, facilitating the categorization of chairs based on their strength under cyclic loads. Notably, the study revealed substantial variations in the load capacity among different chair models. As a consequence of this investigation, the study established acceptable design load thresholds. For instance, concerning front-to-back loading, it was determined that the chairs with cyclic load capacities ranging from 932 to 1449 N fell within the category of low-strength, between 1450 and 1968 N were classified as medium-strength (suitable for domestic use), and the chairs with cyclic load capacities exceeding 1968 N were considered to possess high strength (intended for hotel lobbies, restaurants, libraries, etc.). Similarly, for back-to-front loading performance, the study identified the chairs with cyclic load capacities between 625 and 895 N as low-strength, 896 and 1167 N as medium-strength, and the chairs with loads surpassing 1168 N as high-strength. The performance thresholds for side thrust loads were as follows: low-strength encompassed the cyclic load capacities ranging from 649 to 934 N, medium-strength spanned the cyclic load capacities between 935 and 1221 N, and high-strength entailed 1222 N and above. Notably, the classification devised in this study is closely aligned with the widely accepted and internationally recognized ALA specification. This strong consistency with global standards reinforces the reliability and applicability of the classification system developed in this research. In conclusion, this study enhances understanding of wooden chair strength performance and offers practical insights that lead to higher-quality products and improved consumer satisfaction. Its recommendations can potentially drive positive change within the industry and benefit manufacturers and consumers.
In this study, the lightest possible design of the Warren truss bridge is aimed for a fixed span distance. Optimum structure has been achieved by the Gradient-Descent method. The total weight of the bar elements that make up the whole structure is used as the objective function. The size of the bars in the span and the heights of the vertical bars are assigned as design variables. The minimum natural vibration frequencies of the rods as compressive and tensile strength, buckling resistance and dynamic restraint are limited or defined within certain ranges. The constraints are included as logarithmic barrier functions. Some important results of this study are that with an increase in the number of gaps, the final optimum structure becomes slightly heavier, the shape of the optimum structure shows a curve close to a parabola, and the optimum structure becomes more rigid in the vertical direction when dynamic constraints are included in the process.
Bu çalışmada, bir enerji dağıtım sisteminin, başlangıçtaki yatırım giderlerinin, güç kayıplarının, zaman içerisinde olacak bakım-onarım giderlerinin ve sistemin maddi getirisinin dahil edildiği, çeşitli kapasitede güç gereksinimi ve şebeke uzunlukları için maliyet analizi gerçekleştirilmiştir. Kazancın en yüksek durumda olabilmesi için yeterli sayıda ve gereklilikte özdeş transformatörün sayıca miktarı incelenmiştir. Bunun için, en yüksek kazanç ve en kısa amortisman süresi dikkate alınmıştır. Küçük kesitli kablo olarak Swallow, büyük kesitli kablo olarak Hawk türü kablolar kullanılmıştır. Kalın kesin kesitli kabloların enerji kaybını önlemek için etkili olduğu, ancak gerçekte çok büyük maliyetin transformatörün kapasitesine bağlı olarak kendisinin neden olduğu gösterilmiştir. İdeal sayıda transformatörün tespiti için tek başına en yüksek kazancı ya da en kısa amortisman süresini almak yerine bu ikisinin birbirine en yüksek oranının ele alınmasıyla çok amaçlı bir optimizasyon problemi çözülmektedir.